Bedienungsanleitung NAD T 775 (Seite 21 von 46) (Englisch)

602917

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

AUDYSSEY MultEQ XT ROOM ACOUSTICS CORRECTION

Sound reecting from room boundaries can disturb the spatial illusion

of surround sound, and can also distort the tonal balance of the system.

Professional Acoustical Engineers often add wall treatments and even move

walls and relocate speakers to improve system performance, but for the

average Home Theatre, this is either too expensive or just not a practical

solution.

Audyssey MultEQ XT, using multiple measurements from the actual

listening positions, and processing this information using very sophisticated

digital signal processing, is able to “precondition” the signal to eectively

make the walls disappear. This creates a ‘family size’ sweet spot where the

sound and spatial cues are very accurately reproduced.

MultEQ XT is designed to tame room acoustics without changing the sonic

character of your loudspeakers. While it will make the most of whatever

loudspeakers you have, it will not make poor speakers sound like good

ones!

Connect the Audyssey microphone jack into the front panel’s MP/MIC input

and the Audyssey Auto Calibration wizard will guide you through a simple

step-by-step conguration. Once setup and calibrated, the next greatest

improvement in performance is obtained by eliminating the acoustic

interference caused by room boundaries interacting with your speakers.

MEASUREMENT IS THE FIRST STEP

The sound at each listening position (up to 8 positions) is calibrated using

the same microphone used during the setup phase.

A special test tone is sent to each speaker and the data is memorized by

the T 775. The duration of calibration may take some time depending on

the number of speakers as well as the number of measuring points. After

all positions are measured, the DSP calculates the ideal system response for

your particular room and speaker setup.

If some inconsistencies or discrepancies are detected during the Audyssey

calibration, the process maybe interrupted or the problem is shown in the

particular setup window. A notice screen is correspondingly displayed.

After following and undertaking the displayed instructions, re-start the

Audyssey calibration again. When the measurements are nalized, Audyssey

calculates the ideal system response for your particular room and speaker

setup.

NOTE

 Thetesttoneemittedduringmeasurementisloud.Thismaybe

bothersomeforyouandmayaectyourotherhouseholdmembersas

well,andevenyourneighbor.

NEXT A TARGET CURVE MUST BE CHOSEN

Because loudspeaker designers assume that their products will be used in

typical domestic rooms, they are ‘voiced’ to work in this environment. It is

assumed that the room will add some bass reinforcement and will absorb

some treble energy. Thus if we eectively ‘remove the walls with room

correction, and set the speakers for at response, you may nd this sounds

too bright in the treble and too weak in the bass region.

NAD engineers have done extensive research in this area of room acoustics,

and along with Audyssey engineers developed what we believe is the ideal

‘in room’ response curve. We include this NAD EQ, along with an Audyssey

developed EQ as the two best choices. The response curves shown below

typify NAD EQ room correction process.

Room Response measured by Audyssey microphone

Inverse Correction Filter calculated by NAD T775

Corrected Room Response

Flat EQ is a third option, but not one that we recommend for listening

(it is useful for verifying system performance when using external

instrumentation).

Select the Target Curve you nd to be most satisfactory by pressing the

Audyssey key of the remote. The MultEQ XT corrected response can also be

bypassed if you wish.

It is recommended that you take full advantage of the T 775’s Audyssey

Auto Calibration feature for your speaker setup. However, if you desire to

setup your speakers manually or if you already had run Audyssey Auto

Calibration but would like to make adjustments, the following sections on

Speaker Conguration, Speaker Levels and Speaker Distance can also be

followed and implemented.

NOTE

 Duringmanualsettingofyourspeakers,previouslycalibrated

Audysseysettingscouldberetrievedbyre-adjustingbackthealtered

congurationsashighlightedbyanasterisk.

OPERATION

USING THE T 775  SETUP MENU

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 775 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 775

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info