Bedienungsanleitung NAD T 775 (Seite 39 von 46) (Englisch)

602917

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

MACRO COMMANDS

A “macro” command is a series of two or more remote codes issued automatically from a single

keypress. You might use a macro to automate a simple command sequence, such as, “Turn on the DVD

player and then press PLAY”. Or you might compose an elaborate macro to power up an entire system,

select a source, choose a Listening Mode, and begin playback—again, all from a single keypress. The

HTR 3 can store one macro on each of its function keys (these exclude the Device Selector keys).

NOTE

 Macrosareindependentofthecurrentlyselecteddevice.

RECORDING MACROS

To record a macro, simultaneously press-and-hold for 3 seconds both the [MACRO] key and the HTR 3

function key to which you wish to assign the macro, until the status LED turns green. The macro

button will also light up.

Press the sequence of function keys to be recorded into the macro, being sure to rst press the

requisite Device Selector key for each function (you may switch devices while recording the macro as

many times as necessary), allowing you to create macro containing commands from more than one

Device Selector “page.”

When you have nished entering the desired command sequence, press [MACRO] again

to store the macro; the Learn LED and [MACRO] key illumination will turn o.

NOTE

 Eachmacrocanstoreamaximumof64commandsteps.Ifyouexceedthisnumber,themacrowill

bestoredautomaticallyafterthe64thcommandisadded.

Example: Record a Macro to the [0] key to Turn on the T 775, Select “Input 1” (Source 1), and

Commence Playback of connected Source 1 device (as in DVD player):

• On the HTR 3, simultaneously press-and-hold [MACRO] and [0] (numeric zero); the Learn LED turns

steady green.

• Press [AMP]; press [ON]; press [1] (“Input or Source 1”); press [DVD]; press [ ] (Play) - the Learn LED

blinks as each step is added.

• Press [MACRO] again to exit the macro-record mode.

To clear a macro, perform the above steps without entering any functions.

EXECUTING MACROS

To execute a macro, press and release [MACRO]; its key illumination lights for 5 seconds. While it

remains lit, press an HTR 3 key to which a macro has previously been stored.

The corresponding macro will run; as each step executes, its “parent” Device Selector’s key ashes lights

briey; when execution is nished, the [MACRO] key illumination goes out. Pressing any other HTR 3

key while a macro is executing will abort the macro. Remember that you must hold the HTR 3 so that

its infrared emitter can activate the target components.

NOTE

 Whenamacroexecutes,a1seconddelayisautomaticallyinsertedbetweenitscommands.If

youneedmorethana1seconddelaybetweenparticularcommands—forexample,topermita

componenttopowerupcompletely—youcanrecord“empty”stepsintothemacrobychanging

DeviceSelector“pages”withoutenteringactualcommandfunctions.

BUTTON ILLUMINATION TIMEOUT

The HTR 3’s key-illumination can be set to remain lit for 0-9 seconds. The default value is 2 seconds. To

set the illumination timeout, simultaneously press-and-hold for 3 seconds both the HTR 3’s [DISP] and

the [0-9] key, with the digit corresponding to the desired timeout duration; the Learn LED will ash

twice to conrm the new setting. When set to zero, the illumination will not turn on at all.

NOTE

 KeyilluminationisthebiggestdrainontheHTR3’sbatteries.Ashortkey-illuminationtimeoutwill

extendbatterylifeappreciably;turningitoaltogether(setitto0seconds)willlengthenitstill

further.

OPERATION

USING THE HTR 3 REMOTE CONTROL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 775 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 775

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info