Bedienungsanleitung NAD T748v2 (Seite 9 von 40) (Englisch)

602906

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

6 DAB MODULE INPUT (230V version model only)

The T 748 is compatible only with the NAD DAB Adaptor module

models DB 1 or DB 2.

• Plug-in the other end of the Mini-Din connector from the NAD DAB

Adaptor module output port into this socket.

• With DAB, you can receive CD-like quality programs without any

annoying interference and signal distortion.

• Refer also to the “LISTENING TO DAB RADIO” segment of the

“OPERATION” section.

NOTE

The external NAD DAB Adaptor module is not supplied with your T 748.

7 HDMI (HDMI 1-4, HDMI MONITOR OUT)

• Connect the sets of HDMI input to the HDMI OUT connectors of

source components such as DVD player, BD player or HDTV satellite/

cable box. Connect the HDMI Monitor OUT to a HDTV or projector

with HDMI input.

WARNING

Before connecting and disconnecting any HDMI cables, both the T 748

and the ancillary source must be powered OFF and unplugged from the

AC outlet. Failure to observe this practice may cause permanent damage

to all equipment connected via HDMI sockets.

8 DIGITAL AUDIO (COAXIAL 1-2, OPTICAL 1-2)

• Connect to the corresponding optical or coaxial digital output of

sources such as CD or BD/DVD players, digital cable box, digital

tuners and other applicable components.

• Coaxial and Optical digital input association is congurable via the

Source Setup item of the Setup Menu OSD.

9 IR IN

• This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow

control of the T 748 from a remote location.

10 MP DOCK

The T 748 is equipped with a data port in the rear panel where an

optional NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later

variants can be plugged in.

• Connect the “MP DOCK (DATA PORT)” jack of the T 748 to the

corresponding “DATA PORT” socket of the optional NAD IPD model.

• AUDIO 2 IN and S-VIDEO IN are the assigned default ports for the

audio/video output of the separately sold NAD IPD (NAD IPD Dock

for iPod) 1, NAD IPD 2 and later variants.

• Refer also to the “LISTENING TO YOUR iPod PLAYER” segment of the

“OPERATION” section.

NOTE

The NAD IPD Dock for iPod is not supplied with your T 748.

11 RS 232

NAD is a certied partner of AMX and Crestron and fully supports

these external devices. Check out the NAD website for information

about AMX and Crestron compatibility with NAD. See your NAD audio

specialist for more information.

• Connect this interface using RS-232 serial cable (not supplied) to

any Windows compatible PC to allow remote control of the T 748

via compatible external controllers.

12 AUDIO PRE-OUT

• The AUDIO PRE- OUT makes it possible to use the T 748 as a pre-

amplier to external power ampliers for some or all channels.

Connect FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-BL and

SURR-BR to the respective channel input of a power amplier or

ampliers driving the corresponding applicable speakers.

• Unlike the full range channels, there is no power amplier built-into

the T 748 for a subwoofer. Connect the SUBW output to powered

(“active”) subwoofers or to power amplier channels driving a

passive system.

NOTE

Never connect both the external amplier and T 748’s speaker outputs to

the same set of speakers.

13 SPEAKERS

• Connect the respective speaker’s FRONT L, FRONT R, CENTER,

SURR R, SURR L, SURR-BACK L, and SURR-BACK R channels to their

corresponding loudspeakers. Make sure the “+” (red) terminal and

“-” (black) terminal are connected to the corresponding “+” and “-”

terminals of the loudspeaker. Use extra care to ensure that no stray

wires or strands cross between posts or terminals at either end.

• The T 748 is designed to produce optimum sound quality when

connected to speakers with impedances within its operating range.

Please make sure that all the speakers are rated 8 ohms minimum

per speaker.

NOTE

Use stranded wire of at least 16 gauge (AWG). Connections to the T 748 can

be made with banana-type plugs. Bare wire or pins can also be used by

loosening the terminal’s plastic nut, making a clean, neat connection, and

re-tightening carefully. To minimize the danger of short circuit, ensure that

only 1/2-inch of exposed wire or pin is employed when connecting.

14 AC MAINS INPUT

The T 748 comes supplied with a separate detachable mains power

cord. Before connecting the plug to the mains power source, ensure

that it is rmly connected to the T 748’s AC Mains input socket rst.

• Connect only to the prescribed AC outlet, i.e., 120V 60 Hz (for 120V

version models only) or 230V 50 Hz (for 230V version models only).

• Always disconnect the mains power plug from the mains power

source rst, before disconnecting the cable from the T 748’s AC

Mains input socket.

15 SWITCHED AC OUTLET

This convenience outlet can supply switched power to another

component or accessory.

• The total draw of all devices connected to this outlet must not

exceed 100 watts.

• It is powered ON and OFF by the front panel STANDBY button or by

the AVR 4’s ON and OFF keys.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

NAD T748v2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T748v2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info