Bedienungsanleitung NAD VISO TWO (Seite 7 von 34) (Englisch)

602923

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

WHAT’S IN THE BOX

Packed with your VISO TWO you will nd

• An AM loop antenna.

• A FM ribbon-wire antenna with balun.

• A removable AC cable (if you wish, any IEC-standard AC cable of suitable

wattage may be substituted).

• The HTR 6 remote control with 4 (four) AAA batteries.

• This owner’s manual.

SAVE THE PACKAGING

Please save the box and all of the packaging in which your VISO TWO

arrived. Should you move or otherwise need to transport your VISO TWO,

this is by far the safest container in which to do so. We’ve seen too many

otherwise perfect components damaged in transit for lack of a proper

shipping carton, so please: Save that box!

CHOOSING A LOCATION

Choose a location that is well ventilated (with at least several inches to

both sides and behind), and that will provide a clear line of sight, within

23 feet/7 meters, between the VISO TWO’s front panel and your primary

listening/viewing position—this will ensure reliable infrared remote control

communications. The VISO TWO generates a modest amount of heat, but

nothing that should trouble adjacent components.

It is especially important that sucient ventilation be provided. If you

are contemplating on locating the VISO TWO within a cabinet or other

furniture, consult your NAD audio/video specialist for advice on providing

adequate airow.

QUICK START

In case you simply cannot wait to experience the performance of your

new NAD VISO TWO, we provide the following “Quick Start” instructions to

get you underway. Before the steps below, connect your VISO TWO to a

TV/monitor.

Please make all the connections to your VISO TWO with the unit unplugged.

It is also advisable to power-down or unplug all associated components

while making or breaking any signal or AC power connections.

PLAY A CD OR DVD MOVIE

• Connect the VISO TWO’s composite Video or S-Video “MONITOR OUT”

jack to your TV/monitor’s corresponding input.

• Connect your speakers to the VISO TWO’s “L” and “R” terminals. Make

sure to connect red to red (“+”) and black to black (“-”) with care to

avoid stray wires or strands crossing between terminals. If your system

includes a powered subwoofer, connect the VISO TWO’s “SUBWOOFER

PRE-OUT” jack to its line input.

• Connect the AC cord to the AC inlet and then plug into an AC outlet;

the LED indicator around the POWER button will be illuminated amber

indicating the VISO TWO is in standby mode ready to accept commands

from either the front panel power button or the HTR 6 remote.

• Press “DVD” at the HTR 6 remote’s Device Selector section and then

“OPEN/CLOSE” button.

• Insert the media and press [ PLAY] button to start playback.

You should hear sound from VISO TWO, and see an image on the

TV/monitor. (If one or the other fails to appear, check your TV/monitor’s

input settings or VISO TWO’s audio/video connections).

Enjoy the movie or music, but be sure to set aside time to read this manual

thoroughly, and to set up, calibrate, and congure your VISO TWO carefully

and completely.

INTRODUCTION

GETTING STARTED

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD VISO TWO Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD VISO TWO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info