Bedienungsanleitung NAD VISO TWO (Seite 30 von 34) (Englisch)

602923

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

EXECUTING MACROS

To execute a macro, press and release [MACRO]; its key illumination lights

for 5 seconds. While it remains lit, press an HTR 6 key to which a macro has

previously been stored.

The corresponding macro will run; as each step executes, its “parent” Device

Selector’s key ashes lights briey; when execution is nished, the [MACRO]

key illumination goes out. Pressing any other HTR 6 key while a macro is

executing will abort the macro. Remember that you must hold the HTR 6 so

that its infrared emitter can activate the target components.

NOTE

 Whenamacroexecutes,a1seconddelayisautomaticallyinserted

between its commands. If you need more than a 1 second delay between

particularcommands—forexample,topermitacomponenttopowerup

completely—youcanrecord“empty”stepsintothemacrobychanging

DeviceSelector“pages”withoutenteringactualcommandfunctions.

BUTTON ILLUMINATION TIMEOUT

The HTR 6’s key-illumination can be set to remain lit for 0-9 seconds. The

default value is 2 seconds. To set the illumination timeout, simultaneously

press-and-hold for 3 seconds both the HTR 6’s [DISP] and the [0-9] key, with

the digit corresponding to the desired timeout duration; the Learn LED will

ash twice to conrm the new setting. When set to zero, the illumination

will not turn on at all.

NOTE

 KeyilluminationisthebiggestdrainontheHTR6’sbatteries.Ashort

key-illuminationtimeoutwillextendbatterylifeappreciably;turningit

oaltogether(setitto0seconds)willlengthenitstillfurther.

FACTORY RESET

The HTR 6 can be reset to its factory state, deleting all learned commands,

copied and punched-through keys, macros, and other setup information,

reverting all keys to their pre-programmed library commands.

To perform a factory reset simultaneously press-and-hold for 10 seconds

the HTR 6’s [ON] and [RTN] keys; the Learn LED will start to ash green.

Release [ON] and [RTN] before the second ash is complete; the Learn LED

will turn red, indicating the remote has been reset.

NOTE

 Youmustrelease[ON]and[RTN]beforethesecondashgoesout,otherwise

theunitwillnotreset;shouldthisoccur,repeatthefullprocedure.

DELETE MODE

The HTR 6 can store learned, copied, and “default library” commands on any

single key (The default library commands are the pre-programmed NAD

codes, such as the native VISO TWO commands on the [AMP] “page.”).

You can delete commands by layers back “down” to the default library

command on any key, removing learned commands, punched-through

functions, and copied keys.

NOTE

The default library commands cannot be deleted, so you need not worry

thatusingDeleteModemightcauseirreparablechanges.

To enter Delete Mode, simultaneously press-and-hold for 3 seconds both

the desired key’s Device Selector key and the [RTN] key, until the Learn LED

turns green. Press the function key whose command you wish to delete;

the Learn LED ashes; the number of times indicates which type of function

has become active - see the table below. Press the active Device Selector

key again to exit Delete Mode.

NOTE

 Youmaydeletemultiplefunction-keycommandsonthesameDevice

Selector“page,”buttodeletefrommorethanoneDeviceSelectorpage

youmustexitDeleteModeandthenre-enteritontherequiredpage.

Flashes Command Type

1 Default Library Command

2 Copied Library Command

3 Learned Command

OPERATION

USING THE HTR 6 REMOTE CONTROL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD VISO TWO Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD VISO TWO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info