Bedienungsanleitung Naim HDX (Seite 6 von 32) (Englisch)

707495

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Installation - Getting Started

2 Getting Started

The HDX should be installed horizontally on a dedicated equipment stand intended for the

purpose. Do not stand the HDX directly on top of another item of equipment. Ensure that

the fan aperture on the rear panel is not obstructed. The HDX should be installed in its final

location before connecting cables or switching on. Remember to install batteries in the

remote handset.

The HDX can be connected to a computer network to retrieve album data and artwork

from the internet, to stream music around the home using NaimNet hardware, or to take

advantage of one of its alternative user interfaces. If the HDX is to be used in a network it

is important that the network is working when the HDX is connected and switched on.

Locally connected audio amplifiers should not be switched on before the HDX is switched

on. The HDX power switch is located on the rear panel with a shutdown button located on

the front panel. The front panel shutdown button extinguishes when the HDX wakes from

shutdown.

To begin installation first identify the rear panel network, audio output and mains input

sockets, and connect the appropriate cables.

2.1 Internet/Network Connections

While the HDX can be used in “stand-alone” mode without

any network connection, if its full capabilities are to be

realised it requires connection to an “always on” internet

service via an ethernet router/modem with a built-in

firewall.

If the HDX is to be used in a NaimNet/StreamNet network

audio system, the network connection also enables the

HDX to communicate with other network devices and

provides access to its alternative user interfaces.

The HDX is set up when originally shipped not to require

any further network configuration but to connect to

a network automatically (it uses DHCP by default).

However, if your HDX has been previously used, its network

configuration may have been altered leaving it unable to

connect automatically. Contact your retailer, installer or

Naim Audio directly if this appears to be the case.

Note: An HDX used in stand-alone mode and switched

on without a working network connection will revert to

an internal IP address only suitable for stand-alone use.

To restore the default DHCP setup, switch the HDX off,

connect the network and switch it on again.

2.1.1 Network Hardware

Wired network connection is strongly recommended for

the most consistent and secure HDX operation.

Ethernet-over-mains hardware may be used and provides

a simple and convenient method of home network

connection. However, depending on mains wiring factors

specific to each home environment, the presence of

network data on the mains supply may compromise

overall system sound quality. If any sound quality

compromise is found to be unacceptable, dedicated

network cabling should be installed.

2.2 Power Supply Upgrade

The HDX can be upgraded through the use of an external

Naim XPS or CD555PS external power supply to power its

analogue circuits.

If an external power supply is to be used, the link plug in

the rear panel of the HDX should be removed and the

power supply connected in its place using an SXPS Burndy

cable. See Diagram 3.3.

THE SXPS BURNDY CABLE ONLY MUST BE USED TO CONNECT

THE XPS OR 555PS POWER SUPPLIES.

Both the HDX and the external power supply must be

switched off when the link plug is removed and the Burndy

connections are made. Switch on the external power

supply first followed by the HDX.

2.3 Audio Connections

Connect one or all of the analogue DIN (output 1) or

Phono (output 2) output sockets, or the Digital output

socket, to an appropriate audio system input. If using the

analogue outputs use a Naim Hi-Line interconnect cable

for best results.

Note: The output selector on the rear panel should be

switched to reflect the analogue output connections used.

2.3.1 Signal Ground

Switch the HDX’s rear panel Signal Ground switch (see

paragraph 3.2.14) to the Chassis position unless the HDX is

connected in a hi-fi system incorporating another earthed

source component, or mains “hum” is audible through the

loudspeakers. Contact your retailer, distributor or Naim for

advice if necessary.

Note: All Naim CD players are earthed so the Signal

ground switch should be set to floating if one is connected

in the system.

Note: “Connected” in this context means an analogue

audio signal cable that includes an earth connection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim HDX Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim HDX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info