Bedienungsanleitung Naim NAIT 5SI (Seite 15 von 22) (Englisch)

707500

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

E13

12. NAIT 5si

The NAIT 5si is a very high performance stereo integrated amplier that combines a preamplier providing four line-level

analogue inputs with a power amplier rated at 60 Watts per channel. The NAIT 5si can be controlled by either its remote

handset or by a front panel mounted volume knob and input selection buttons. The NAIT 5si remote handset is described in

Section 15 of this manual. A front panel 6.3mm jack socket enables the use of headphones with the NAIT 5si.

Your NAIT 5si should be installed on a dedicated equipment stand intended for the purpose. Do not stand it directly on top

of another item of equipment. Care should be taken to ensure that it is level. The amplier should be installed in its nal

location before connecting cables or switching on. Ensure that the volume is turned down before switching on.

12.1 Mains Power Connection

Connect the NAIT 5si to a mains power socket using either

the mains cable supplied or a Naim Power-Line.

12.2 Signal Inputs

The front panel input selector buttons select the source

input signal to be routed to the power amplier and

the loudspeakers or headphones. The four buttons are

labelled cd, tuner, hdd (hard disk drive) and av. Each input

button corresponds to a pair of rear panel RCA phono

input sockets. The cd and tuner inputs are additionally

provided with parallel DIN sockets. These should be used

in preference to the RCA phono sockets if practical. Do not

connect both the DIN and RCA phono sockets of one input

simultaneously.

12.3 Speaker Outputs

A stereo set of speaker connection sockets is provided

on the rear panel. The sockets can accept standard 4mm

plugs, but to comply with European legislation the Naim

connectors supplied should be used. Naim Audio speaker

cable will provide the best results; however, a wide range of

speaker cable types can be used without risk of damage to

the amplier.

Ensure when connecting speakers that they are “in phase”.

That is, the positive and negative connection orientation at

both the speaker and amplier ends of the cable is the same

for both channels.

12.4 hdd Output

The NAIT 5si hdd input has an associated output that enable

the selected input signal to be routed externally; to an audio

recording component for example.

Note: The hdd output remains active regardless of which

input is selected. Take care that a feedback loop is not

inadvertently created by the simultaneous selection of

input and output. The hdd output will be silenced when

mute is engaged.

12.5 Headphone Output

The NAIT 5si headphone output is able to drive the majority

of headphone types. The 6.3mm (1/4”) jack socket, rather

than the smaller 3.5mm jack socket, provides more reliable

connection and potentially higher sound quality. Most

high-quality headphones are supplied with an adaptor that

enables use with either 3.5mm or 6.3mm jack sockets.

Inserting a headphone plug will mute the NAIT 5si speaker

outputs. Removing the headphone plug will restore the

outputs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NAIT 5SI Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim NAIT 5SI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info