Bedienungsanleitung Naim NAIT 5SI (Seite 17 von 22) (Englisch)

707500

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

E15

NAIT 5si

Automatic Input Switching only becomes operational on exit

from program mode by pressing and holding the handset

prog key.

Note: The NAIT 5si will leave program mode automatically

if no control commands are received for ve minutes.

Note: In a few cases some further equipment

conguration may be required for auto switching to

operate correctly. Please contact your retailer or local

distributor for advice.

14.2 AV Bypass

The NAIT 5si can be integrated within a multi-channel home

theatre system, driving the front left and right channel

speakers, by engaging its AV Bypass mode. AV Bypass mode

enables a home theatre processor to take over volume control

of signals connected to the NAIT 5si av input.

To select AV Bypass, rst switch the NAIT 5si into program

mode by pressing and holding the handset prog key (with

the handset in preamplier mode). The front panel av button

will illuminate if AV Bypass is selected. If it is not enabled it

can be switched on by pressing av button twice.

The NAIT 5si volume control indicator will extinguish when

AV Bypass mode is engaged and the av input is selected.

Remote handset volume control and mute function will also

be disabled.

Note: The AV Bypass feature must be used with care. It

bypasses the NAIT 5si volume control leaving any signal

connected to the av input to be passed to the speakers at

full volume.

Note: Inserting a headphone plug while AV Bypass mode

is selected temporarily returns the NAIT 5si to normal

operation. Removing the headphone plug will return the

NAIT 5si to AV Bypass mode.

Note: The mute function is disabled when AV Bypass

mode is engaged.

14.3 Handset Volume Control

The remote handset volume keys provides some alternative

control characteristics. A short press and release of a key

will adjust by a preset “nudge”, while pressing and holding

the key will result in three seconds of slow adjustment

followed by continual fast adjustment.

Note: The NAIT 5si does not incorporate any facility for

channel balance adjustment.

14.4 Mute

Mute silences the outputs and can be selected or

deselected by pressing the remote handset mute key.

14.5 Display

The NAIT 5si front panel button illumination can be

switched o by pressing the remote handset (in preamplier

mode) disp function. Any subsequent handset or front panel

operation will temporarily restore the display. A second

operation of the disp function will restore the display.

14.6 Remote Control

The NARCOM 5 remote handset supplied with the

NAIT 5si duplicates all conguration and control functions.

See Section 15 for more information.

14.7 Defaults

To restore all NAIT 5si programmable settings to the factory

defaults press and hold the remote handset disp key while

the unit is in program mode. The NAIT 5si will exit from

program mode following this operation.

14.8 Fault Conditions

The NAIT 5si will indicate fault conditions by ashing front

panel button buttons. The following table lists the fault

indications.

Fault Flashing Button

Excess Temperature cd

Excess Current tuner

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NAIT 5SI Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim NAIT 5SI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info