Bedienungsanleitung Naim NAT05 XS (Seite 5 von 34) (Deutsch, Englisch, Französisch, Italienisch)

707498

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

NAT05 XS Installation

4 NAT05 XS Installation

The NAT05 XS should be installed on a dedicated equipment stand intended for the

purpose. Do not stand it directly on top of another item of equipment. It should be

installed in its final location before connecting cables or switching on. Ensure also that the

system volume is turned down before switching on.

A number of power supply upgrade options are possible for the NAT05 XS. A diagram

illustrating the connection of one of these is shown in Section 7. Contact your local retailer

or distributor for advice if necessary on power supply connection.

4.1 Aerial Requirements

The NAT05 XS aerial input socket must be connected via

75Ω low-loss coaxial cable to a suitable aerial.

Ideally the aerial should be mounted on the roof, clear

of obstructions and as high as possible. Use of an aerial

preamplifier may disturb the muting operation of the tuner

and may cause cross-modulation problems (interference

from an adjacent strong radio broadcast). Such

preamplifiers should only be used as a last resort.

Radio broadcasts are usually transmitted from different

sites even though the target areas of the services may be

similar. This means that unless the transmitters are in almost

the same direction looking from your house, an aerial

aligned on one transmitter will give less than optimum

performance on the other. In these circumstances you

should fit an aerial rotator, or a less directional aerial if

appropriate. The more sensitive and directional the aerial

you use, the worse will be the reception in directions other

than the one towards which the aerial is pointing. If you

are particularly interested in receiving a wide range of VHF

transmissions an aerial rotator is a necessity. Your retailer

will be familiar with local conditions and will be able to

advise you on which stations you can expect to receive

satisfactorily.

4.2 Audio Outputs

The NAT05 XS is fitted with both DIN and RCA-phono output

sockets. Use of the DIN option is preferred, however, if the

RCA-phono option is to be used it must be selected once

the NAT05 XS is switched on. Section 5.2 describes output

socket selection.

4.3 Power Supply Upgrades

The NAT05 XS can be upgraded through the addition of

an external FlatCap or Hi-Cap power supply. The external

supply works with the internal power supply of the NAT05 XS

to offer both a greater number of separate supplies and

more sophisticated voltage regulation.

The upgrade power supply is connected to the NAT05 XS

via a 240° five-pin DIN cable. Ensure that both the power

supply and NAT05 XS are switched off when making

connections. Remove the link plug and connect the supply

cable ensuring that the connectors are securely attached.

From their respective power switches, switch on the power

supply followed by the NAT05 XS. Diagram 7.2 illustrates the

connection of an external power supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NAT05 XS Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info