Bedienungsanleitung Naim NAT05 XS (Seite 6 von 34) (Deutsch, Englisch, Französisch, Italienisch)

707498

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

NAT05 XS Operation

5.1 Front Panel Buttons and Handset Keys

The NAT05 XS can be operated either from its front panel

buttons or from the remote handset (switched to tuner

mode). The handset also provides control of station preset

memory and recall facilities. Section 6.1.3 describes preset

memory and recall. The front panel buttons and handset

keys operate as follows (handset keys are shown in

brackets):

mode: Toggles the tuner through three operational

modes: frequency, scan and preset. Preset

mode is covered further in Section 6.1.3.

down: In frequency mode, the down button or left (3)

(3) key adjusts tuning frequency downwards in

50kHz steps or continuously if held.

In scan mode, the down button or left (3) key

causes the tuner to “scan” down the FM band

searching for signals above a preset level. The

tuner will stop at each tuned station and, using

the remote handset, the option to store the

station as a preset will be available (see Section

6.1.3). If no satisfactory signals are found during

the first scan, a second scan at a lower preset

signal level will automatically commence.

In preset mode, the down button or left (3)

key causes the tuner to step sequentially down

through previously stored stations.

up: Controls the tuner in a similar manner to the

(4) down button and left (3) key.

mono: Combines the left and right channels to

(mon) produce a mono output signal. Switching to

mono can reduce background noise with weak

stereo signals. The mono setting is stored when a

station is saved as a preset.

Note: The front panel mono button indicator will illuminate

when mono is selected.

5.2 Output Socket Selection

A pair of RCA-phono output sockets are fitted on the

NAT05 XS rear panel to provide an alternative to the

preferred DIN socket. Proceed as follows to select the RCA-

phono sockets.

Press and hold the remote handset mode key (handset

in tuner mode), or the front panel mode button, until

the mode button indicator flashes. Further operations

of the mode key or button will now cycle through each

combination of the two socket types (DIN only, RCA-phono

5 NAT05 XS Operation

Once the NAT05 XS is installed and all connections are secure it can be switched on. If an

upgrade power supply is connected this should be switched on first. After switch-on the

tuner will remain muted for 25 seconds while control systems and circuits stabilise. During

this time all four front panel buttons will illuminate.

only or both). The selected option is indicated on the tuner

display as shown below:

Socket Option Tuner Display

DIN O

Phono

Both O

To avoid compromised sound quality, do not select both

socket types unless their simultaneous use is unavoidable.

Press and hold the mode key or button a second time to

exit from socket selection mode. Socket selection mode

will automatically exit after five minutes if no key or button

is pressed.

5.3 Front Display and Indicators

The NAT05 XS front panel display and indicators provide

visual feedback on tuner operation.

Display

Displays tuned frequency, selected preset number or “--”

indicating that no preset number is allocated to a specific

tuned frequency. Allocation of tuned frequencies to preset

numbers is covered in Section 6.1.3.

Indicators

stereo: Indicates that both a stereo signal is received and

stereo operation is selected.

freq: Indicates that the tuner is operating in frequency

mode.

scan: Indicates that the tuner is operating in scan

mode.

preset: Indicates that the tuner is operating in preset

mode.

5.4 Fault Conditions

The NAT05 XS will indicate that a power supply or link plug is

incorrectly installed by flashing all four front panel buttons.

The output of the tuner will be muted in this state.

If the mains voltage drops too far below its nominal level

the tuner output will be muted and all four front panel

buttons will illuminate. After the mains voltage recovers

there will be a 2 second delay before the output returns to

normal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NAT05 XS Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info