Bedienungsanleitung Naim ND5 XS (Seite 7 von 23) (Englisch)

707490

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Installation and Connection

2.10.3 Network Settings

The NDX/5XS is set up when originally shipped not to

require any on-site TCP/IP configuration but to connect

to a network automatically (it uses DHCP by default).

However, if your NDX/5XS has been previously used, its

network configuration may have been altered leaving

it unable to connect automatically. If this appears to be

the case ensure that DHCP is selected in the Network

Settings menu (see Section 4.5 of this manual) and re-start

NDX/5XS. If problems still persist contact your retailer,

installer or Naim Audio directly.

Note: Before reporting network connection problems carry

out a Factory Reset operation. Select Reset All Settings

from the Factory Settings setup menu. See Section 4.10.

Note: A NDX/5XS switched on without a working wired

network connection will only be able to connect to

a home network wirelessly. To use an Ethernet (wired)

connection, switch the NDX/5XS off, connect the network

and switch it on again.

Note: For internet radio to operate, the NDX/5XS requires

connection to a broadband internet service.

2.11 System Automation

NDX/5XS control can be linked using System Automation

to the control of some Naim preamplifiers, CD players and

the Naim DAC. System Automation enables for example,

preamplifier inputs to be selected via the NDX/5XS, or for

n-Stream transport functions to control a CD player. To take

advantage of System Automation, connect one of the

NDX/5XS rear panel Remote Out sockets to a preamplifier,

CD player or DAC Remote In socket. Use a cable

terminated with a 3.5mm jack plug at one end and a

3.5mm jack or phono plug as necessary at the other end.

Using both NDX/5XS Remote Out sockets, for example, one

connected to a preamplifier and one connected to a CD

player enables comprehensive system control via just one

user interface (handset or n-stream iPhone app).

Note: Stereo and mono 3.5mm jack to 3.5mm jack can

be used for System Automation. If a stereo 3.5mm jack to

phono plug cable is used, connect the left channel phono

plug.

Note: NDX/5XS System Automation is switched off by

default. A full description of its configuration and use can

be found in Section 4.9.

2.12 External Control and Update Sockets

The NDX and ND5 XS are fitted with a 3.5mm jack Remote

In socket on their rear panels. The Remote In socket

can be used for RC5 remote control via a fully wired

connection or a remote IR repeater.

The NDX and ND5 XS are also fitted with a rear panel mini-

USB socket. This socket enables firmware upgrades and

diagnostic tests to be carried out. Contact your retailer for

more information if required.

Note: The rear panel mini-USB socket is not intended for the

connection of USB storage hardware and cannot be used

for audio playback.

2.13 Signal Ground Switch

The NDX/5XS is fitted on its rear panel with a Signal Ground

switch offering two positions: Chassis and Floating. Select

the Chassis position unless NDX/5XS is connected in a hi-fi

system incorporating another earthed source component,

or mains “hum” is audible through the loudspeakers.

Contact your retailer, distributor or Naim for advice if

necessary.

Note: “Connected” in the context above means an

analogue audio signal cable that includes an earth

connection.

Note: All Naim CD players are earthed so the Signal

Ground switch should be set to floating if one is connected

in the system (unless a digital signal connection is used).

Note: The Signal Ground switch setting is not affected by

the use of an external power supply.

No damage will be done if the wrong Signal Ground

position is chosen, however the system sound quality may

be compromised.

2.13.1 General Audio Connection Notes

The NDX/5XS mains earth (ground) should always be

connected regardless of what other equipment is used.

Note: If an external power supply is used the NDX/5XS

mains earth is connected through the Burndy connection

cable to the power supply mains earth.

A mains earth grounds the chassis and the electrostatic

screen within the transformer, and is only connected to the

signal negative if the Signal Ground switch is set to Chassis.

In order to avoid hum loops, the signal negative of the

whole system should be connected to the mains earth in

one place only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim ND5 XS Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim ND5 XS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info