Bedienungsanleitung Naim SUPERNAIT 3 (Seite 10 von 22) (Englisch)

707504

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

8. NAIT XS 3

The NAIT XS 3 is a very high performance stereo integrated amplier that combines a

preamplier providing ve line-level analogue inputs and one moving magnet phono input with

a power amplier rated at 70 Watts per channel. The NAIT XS 3 can be controlled by either

its remote handset or by a front panel mounted volume knob and mute and input selection

buttons. The NAIT XS 3 remote handset is described in Section 15 of this manual. A front panel

6.3mm jack socket enables the use of headphones with the NAIT XS 3.

A variety of power supply upgrade, alternative preamplier and alternative or additional power

amplier options are possible for the NAIT XS 3. A diagram illustrating one option is shown in

Section 10. If no power supply or alternative amplier options are to be employed, the NAIT XS

3 preamp/power amp link plug, supplied in the accessory pack, must be tted to the rear panel

“preamp out” and “power amp in” sockets. The link plug is shown tted in Diagram 9.2.

Your NAIT XS 3 should be installed on a dedicated equipment stand intended for the purpose.

Do not stand it directly on top of another item of equipment. Care should be taken to ensure

that it is level. The amplier should be installed in its nal location before connecting cables or

switching on. Ensure that the volume is turned down before switching on.

8.1 Mains Power Connection

Connect the NAIT XS 3 to a mains power socket using either

the mains cable supplied or a Naim Power-Line.

8.2 Signal Inputs

The NAIT XS 3 front panel input buttons select the source input

signal to be routed to the integral power amplier and the

loudspeakers or headphones. The six buttons are labelled cd,

tuner, stream, av, phono and aux 2.

The cd, tuner, stream and av input buttons correspond to

parallel DIN and RCA phono input sockets on the rear panel.

The phono input button corresponds to a pair of rca phono

sockets compatible with moving magnet (mm) cartridges.

The turntable earth lead should be connected to the ground

terminal when this input is being used.

Note: The stream and av sockets carry both inputs and

outputs. See Section 8.4 for more information.

The aux 2 input button corresponds to a DIN input socket

on the rear panel. The aux 2 DIN socket also carries a power

supply output intended to power a Naim StageLine or

SuperLine phono preamplier.

Note: For optimum sound quality DIN sockets should

always be used in preference to RCA phono sockets.

Note: Where an input has DIN and phono socket options

only one should be connected at any one time.

Always use high quality interconnect cables to connect

sources to inputs. The Naim Hi-Line will produce the best

results.

8.3 Speaker Outputs

A set of stereo speaker connection sockets is provided on

the rear panel. Custom Naim loudspeaker connectors are

supplied to make the connection and in order to comply

with current European safety regulations these should

always be used. Naim speaker cable will provide the best

results, however, a wide range of speaker cable types can

be used without risk of damage to the amplier.

Ensure when connecting speakers that they are “in phase”.

That is, the positive and negative connection orientation at

both the speaker and amplier ends of the cable is the same

for both channels.

8.4 av and stream Outputs

The NAIT XS 3 av and stream inputs have associated

outputs that enable the selected input signal to be routed

externally; to an audio recording component for example.

Note: The av and stream outputs remain active while

their corresponding inputs are selected. Take care that

a feedback loop is not inadvertently created by the

simultaneous selection of input and output.

8.5 Headphone Output

The NAIT XS 3 headphone output is able to drive the

majority of headphone types. The 6.3mm (1/4”) jack socket,

rather than the smaller 3.5mm jack socket, provides more

reliable connection and potentially higher sound quality.

Most high-quality headphones are supplied with an adaptor

that enables use with either 3.5mm or 6.3mm jack sockets.

Inserting a headphone plug will mute the NAIT XS 3 speaker

outputs. Removing the headphone plug will restore the

outputs.

Note: The NAIT XS 3

incorporates an AV Bypass

switch on its rear panel.

The switch should only be

set to “On” if the amplifier

is to be used in conjunction

with an AV processor in a

home theatre system. In

all other installations the

AV Bypass switch should

be set to “Off”. Speaker

and amplifier damage

may occur if a signal is

inadvertently connected

to the NAIT XS 3 av input

while the AV Bypass switch

is “On”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim SUPERNAIT 3 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim SUPERNAIT 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info