Bedienungsanleitung Naim SUPERNAIT 3 (Seite 11 von 22) (Englisch)

707504

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

8.6 AV Bypass

The NAIT XS 3 can be integrated within a multi-channel

home theatre system, driving the front left and right channel

speakers, by engaging its AV Bypass mode. AV Bypass

mode enables a home theatre processor to take over volume

control of signals connected to the NAIT XS 3 av input. It is

engaged using the switch on the rear panel. The

NAIT XS 3 volume control indicator will extinguish when AV

Bypass mode is engaged and the av input is selected. The

remote handset volume control will also be disabled.

Note: The AV Bypass feature must be used with care. It

bypasses the NAIT XS 3 volume control leaving any signal

connected to the av input to be passed to the speakers at

full volume.

Note: Inserting a headphone plug while AV Bypass mode

is selected temporarily returns the NAIT XS 3 to normal

operation. Removing the headphone plug will return the

NAIT XS 3 to AV Bypass mode.

Note: The mute function is disabled when AV Bypass

mode is engaged.

8.7 Other Signal Inputs and Outputs

The NAIT XS 3 incorporates RCA phono sub out, DIN pre-

amp out, and DIN power-amp in sockets on its rear panel. In

normal use the pre-amp out and power-amp in sockets are

connected by a link plug. The link plug should be removed

only in the following circumstances:

• A power supply upgrade is to be used.

• An alternative preamplier is to be used with the

NAIT XS 3 power amplier. See Section 8.8

• An alternative power amplier is to be used with the

NAIT XS 3 preamplier.

Note: The power amp in socket carries a 24V DC power

supply output intended for Naim preampliers that

require an external power supply.

The RCA phono sub out sockets provide a stereo output

intended for connection to an active subwoofer. The output

signal is a duplicate of the preamplier output. No low-pass

ltering is applied.

8.8 Power Amp Mode Operation

If a NAIT XS 3 is to be used as a stereo power amp only it

must be congured to operate in power amp mode:

• With the NAIT XS 3 switched o, remove its rear panel

link plug and connect the interconnect cable from the

preamp or preamp power supply to the power amp in

socket

• Switch on the NAIT XS 3. The mute button will ash to

indicate that the link plug has been removed. Press and

hold the mute button until it extinguishes. The NAIT

XS 3 is now in power amp mode. Its volume control

indicator and button illumination will extinguish.

• To return the NAIT XS 3 to normal operation, switch it

o, replace the link plug and switch it on again.

8.9 Power Supply Upgrades

The NAIT XS 3 preamplier can be upgraded through the

connection of an external Flatcap, Hi-Cap or Supercap

power supply. The NAIT XS 3 and external power supply

must be switched o when connections are made. Switch

on the external power supply rst followed by the NAIT XS 3

when all connections are complete.

8.10 General Connections Notes

The NAIT XS 3 negative input and output connections for

each channel are common. The mains earth (ground) should

always be connected regardless of what other equipment is

used in conjunction with the amplier. The mains earth only

grounds the case and the electrostatic screen within the

transformer, and is not connected to the signal negative. In

order to avoid hum loops, the signal negative of the whole

system should be connected to the mains earth (ground) in

one place.

A signal ground connection is tted to the NAIT XS 3 rear

panel. This is intended to be used to connect a turntable

pick-up arm signal earth only.

8.11 External Control and Interface

The NAIT XS 3 is tted on its rear panel with a 3.5mm jack

Remote In socket and a mini-USB interface socket.

The Remote In socket can be used for RC5 remote control

of the NAIT XS 3 via a wired connection or a remote IR

repeater.

The mini-USB socket enables rmware upgrades and

diagnostic tests to be carried out. Contact your Naim

retailer for more information if required.

Note: The mini-USB interface is not intended for the

connection of USB memory devices.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim SUPERNAIT 3 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim SUPERNAIT 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info