Bedienungsanleitung Naim UnitiQute 2 (Seite 13 von 22) (Englisch)

707489

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

UnitiQute 2 Setup

frequency component of a speaker system incorporating

small (restricted bandwidth) satellite speakers. When

Small is specified, a 100Hz high-pass filter is applied to the

UnitiQute 2 speaker output signal.

Select None when no speakers are connected directly to

the UnitiQute 2

Engaging the Loudness option applies low frequency boost

to the speaker and preamplifier outputs that decreases as

the volume setting is increased. Through compensating for

the ear’s reduced low frequency sensitivity at low volume

levels, the Loudness function can make low volume

listening more satisfying.

Note: The loudness contour operates at volume settings

between 0 and 55.

The speaker Max. Volume and Balance parameters specify

maximum allowed volume, and the channel balance

respectively.

4.5 The Headphones Menu

The Headphones setup menu

enables the Max. Volume

parameter to be specified:

Parameter Options

Max. Volume: 0 to 100 (adjust

using handset 6

or 5 keys)

4.6 The Network Settings Menu

The Network Settings menu

enables UnitiQute 2 network

parameters to be customised

to suit the router and network.

The options are tabulated

and described in the following

sections:

Parameter Options

Name: User definable (text entry)

Default: Uniti-xxxx

Wireless: Not Used / Wireless Network Names

Status: Connected / No Signal / Login Failure /

Busy / Etc.

DHCP: Yes / No

The Name parameter enables the UnitiQute 2 default

network name to be changed.

The Wireless parameter enables a wireless network to be

chosen and joined. See Section 4.6.1 below for detailed

wireless set up notes.

Network Status displays the current network connection

status.

The DHCP parameter enables the UnitiQute 2 network

settings to be modified. In most cases, specifying Yes and

leaving UnitiQute 2 set to DHCP, will be the appropriate

option. See Section 4.6.2 below for notes on non-DHCP

network connection.

Note: Devices installed on a network have an IP address

through which they are identified by all the other items

on the network. DHCP is a set of rules that enable the

automatic allocation of addresses as items are connected

(or switched on while connected) to the network.

UnitiQute 2 is set up by default to use DHCP.

Note: If UnitiQute 2 is connected to the network both

wirelessly and via Ethernet (wired), the Ethernet connection

will take priority.

4.6.1 Wireless Network

Connection Set Up

If the Wireless parameter is

selected in the Network Settings

menu the Select Network menu

will display a list of the available

networks. An option not to use a wireless connection is

also provided. Use the handset up (5) or down (6) keys

to scroll through the list and the ok/list key to select a

network.

Note: UnitiQute 2 is compatible with most commonly used

Wi-Fi standards. Routers that support 802.11b and 802.11g

will work, however those with 802.11n compatibility are

recommended for best results.

Note: As with any wireless network hardware, UnitiQute

2 connection reliability will be affected by both network

router performance and Wi-Fi signal quality. To minimise

the possibility of poor connection reliability, UnitiQute 2

should be connected to network audio sources by no

more than one wireless “leg”. Other “legs” necessary

between UnitiQute 2 and the network audio sources

should be wired.

Note: UnitiQute 2 cannot connect to a “hidden” wireless

network.

If the selected network is secure

and requires a passphrase or

access key to join, UnitiQute 2 will

display an alert message. Pressing

the handset ok/list key will then

open a text entry screen for entry

of the passphrase or access key.

Use the handset numeric/text

keys to enter the passphrase or

access key taking care to ensure

that the letter case is correct.

Press the handset ok/list key

when text entry is complete. In

the illustration the passphrase is

“flatfish”.

If the network is successfully

joined UnitiQute 2 will display a

confirmation screen.

Network Settings 1/4

4Name: Uniti-0131

Wireless: Not Used

Status: Not Connected

DHCP Yes

Headphones 1/1

4Max. Volume: 100

Select Network 3/6

<Don’t Use Wireless>

LingNet

4GreenNet

 TomNet

Now enter your wireless

passphrase or access key.

Press OK to continue

flatfish abc

flatfish

Press OK to confirm

Connected

Press OK To Finish

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim UnitiQute 2 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim UnitiQute 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info