Bedienungsanleitung Napoleon BIP 500RB (Seite 12 von 60) (Englisch, Französisch)

637930

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

www.napoleongrills.com

Burner: The burner is made from heavy wall 304 stainless steel, but extreme heat and a corrosive

environment can cause surface corrosion to occur. This can be removed with a brass wire brush.

CAUtION! Beware of Spiders.

Spiders and insects are aracted to the smell of propane and natural gas. The burner is equipped with an

insect screen on the air shuer, which reduces the likelihood of insects building nests inside the burner

but does not enrely eliminate the problem. A nest or web can cause the burner to burn with a so yellow

or orange ame or cause a re (ashback) at the air shuer underneath the control panel. To clean the

inside of the burner, it must be removed from the gas grill: Remove the screw (s) that aaches the burner

to the back wall. Slide the burner back and up wards to remove. Cleaning: Use a exible venturi tube brush

to clean the inside of the burner. Shake any loose debris from the burner through the gas inlet. Check the

burner ports and valve orices for blockages. Burner ports can close over me due to cooking debris and

corrosion, use an opened paperclip or the supplied port maintenance bit to clean them. Drill out blocked

ports using this drill bit in a small cordless drill. The ports are easier to clean if the burner is removed from

the grill, but it can also be done with the burner installed. Do not ex the drill bit when drilling the ports,

as this will cause the drill bit to break. This drill is for burner ports only, not for the brass orices (jets)

which regulate the ow into the burner. Take care not to enlarge the holes. Ensure the insect screen is

clean, ght, and free of any lint or other debris.

Reinstallaon: Reverse the procedure to reinstall the burner. Check that the valve enters the burner when

installing. Replace sear plate mount and / or ghten screws to complete reinstallaon.

WARNING! Regulator Hose (when applicable): Check for abrasions’, melng, cuts, and cracks in the

hose. If any of these condions exist, do not use the gas grill. Have the part replaced by your Napoleon

Gas Grill dealer or qualied gas installer.

WARNING! When reinstalling the burner aer cleaning it is very

important that the valve/orice enters the burner tube before lighng

your gas grill. If the valve is not inside the burner tube a re or explosion

could occur.

Aluminum Casngs: Clean casngs periodically with warm soapy water. Aluminum will not rust, but high

temperatures and weathering can cause oxidaon to occur on aluminum surfaces. This appears as white

spots on the casngs. To renish these areas, clean rst and sand lightly with ne sandpaper. Wipe the

surface to

remove any residue and paint with high temperature barbecue paint. Protect surrounding

areas from over-spray. Follow the manufacture’s direcons for curing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Napoleon BIP 500RB Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info