Bedienungsanleitung Napoleon BIP 500RB (Seite 13 von 60) (Englisch, Französisch)

637930

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

www.napoleongrills.com

Troubleshoong

Problem Possible Causes Soluon

Low heat / Low ame

when valve turned to

high.

For propane - improper lighng

procedure.

For natural gas - undersized supply

line.

For both gases - improper preheang.

Ensure lighng procedure is followed carefully.

All gas grill valves must be in the o posion

when the tank valve is turned on. Turn tank

on slowly to allow pressure to equalize. See

lighng instrucons.

Pipe must be sized according to installaon

code.

Preheat grill with both main burners on high

for 10 to 15 minutes.

Excessive are-ups/

uneven heat.

Sear plates installed incorrectly.

Improper preheang.

Excessive grease and ash build on sear

plates and in drip pan.

Ensure sear plates are installed with the holes

towards the front and the slots on the boom.

See assembly instrucons.

Preheat grill with both main burners on high

for 10 to 15 minutes.

Clean sear plates and drip pan regularly. Do

not line pan with aluminum foil. Refer to

cleaning instrucons.

Burners burn with yellow

ame, accompanied by

the smell of gas.

Possible spider web or other debris, or

improper air shuer adjustment.

Thoroughly clean burner by removing. See

general maintenance instrucons. Open air

shuer slightly according to combuson air

adjustment instrucons. (This must be done

by a qualied gas installer.)

Flames li away from

burner, accompanied

by the smell of gas, and

possibly dicules in

lighng.

Improper air shuer adjustment. Close air shuer slightly according to

combuson air adjustment instrucons. (This

must be done by a qualied gas installer.)

Rear and Side burners

will not light with the

igniter, but will light with

a match.

Dead baery / or installed incorrectly.

Loose electrode wire or switch

terminal wires.

Liing ames on burner.

Replace with premium heavy duty baery.

Check that electrode wire is rmly pushed

onto the terminal on the back of the igniter.

Check that the lead wires from the module

to the ignion switch (if equipped) are rmly

pushed onto their respecve terminals.

Close air shuer slightly - see previous

problem.

Main burner will not light

with the igniter, but will

light with a match.

Jet-re outlet is dirty or clogged. Clean jet-re outlet with a so bristle brush.

Humming regulator. Normal occurrence on hot days. This is not a defect. It is caused by internal

vibraons in the regulator and does not aect

the performance or safety of the gas grill.

Humming regulators will not be replaced.

Burners will not cross

light each other.

Dirty or corroded cross light brackets. Clean or replace as required.

“Paint” appears to be

peeling inside lid or

hood.

Grease build-up on inside surfaces. This is not a defect. The nish on the lid and

hood is porcelain, and will not peel. The

peeling is caused by hardened grease, which

dries into paint-like shards, that ake o.

Regular cleaning will prevent this. See cleaning

instrucons.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Napoleon BIP 500RB Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info