Bedienungsanleitung Native Massive X (Seite 124 von 133) (Englisch)

707119

124

Zoom out

Zoom in

Vorherige Seite

1/133

Nächste Seite

(5) LFO Level: Amplifies the output of the LFO. Turning the knob right increases the amplification

level.

(6) Polarity: Selects from three Polarity settings (Bi, Uni, Uni Z) that determine how the envelope

in the Amp section behaves.

• When Bi (Bipolar) is selected, the output range of the LFO is -100% to +100%. The waveform

always starts at 0%, independent of which shape is selected.

• Uni (UniPolar) offers a range of 0 to 100%. The waveform will always start at 50%, independ-

ent of the selected shape.

• Uni Z (UniPolar Zero) also has a range of 0 to 100% . The differences between Uni and Uni Z

can only be heard when the oscillator is restarted with a new note trigger. The Polarity setting

is reflected in the modulation.

(7) Delay: Applies a delay to the onset of the LFO. When turned fully left, no delay time is applied

and the LFO starts immediately. Turning the knob right increases the delay time.

(8) Fall/Rise: Adjusts the way the LFO fades in or out. At centre position the LFO has infinite fall-

ing time, working as though it is always on. Turning the knob right produces a short rising ramp

that becomes longer as it is turned fully right. Turning the knob left creates a very small decay fall

time, which extends to a very long falling time as the control is turned fully left. The display, located

below the Fall/Rise knob, provides a visual representation of the shape of the fades.

(9) Mono: When deactivated, the LFO is polyphonic. Each incoming note receives its own LFO.

When activated, the LFO is monophonic and all incoming notes receive the same LFO, regardless

of pitch.

(10) Midi: Switches between Midi and Remote mode for resetting and latching the LFOs. When

Midi is selected the LFO resets and latches based on incoming MIDI note events. If Remote is

selected the LFO resets and latches when you change key switches in the Remote Octave.

(11) Play mode: Selects from six settings (Loop, Loop RST, Loop GTE, Loop REL, 1shot, 1shot

REL), that determine the general behavior of the LFO.

• Loop is the most classic setting, with the LFO running in an infinite loop, regardless of whether

notes are being played or not.

• Loop RST (Loop Restart) also runs in an infinite loop, but will immediately jump to a given

phase if a MIDI trigger is received from Zone or Remote.

• Loop GTE (Loop Gate) follows the same behavior as Loop Restart, but cuts the LFO as soon

as the note is released.

• Loop REL (Loop Release) deactivates the LFO as soon as note is received. When the note is

released, the LFO resets and the modulation is in effect. In this mode, it is important to set a

long release time on the Amp envelope, or the effect will not be heard.

• When 1shot (One Shot) is selected, only one cycle of the LFO will be played. Note on will al-

ways restart the LFO and go to zero after the cycle, regardless of the LFO value or polarity set-

ting. This ensures predictable results, regardless of the LFO waveform.

• 1shot REL (One Shot Release) follows the same principles as 1shot mode, but creates a cy-

cle when the note is released. In this mode it is also important to set a long Release time on

the Amp envelope, or the effect will not be heard.

Modulators

120 Manual

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Native Massive X Seite 124

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info