Bedienungsanleitung Navman FISH 4200 (Seite 6 von 32) (Englisch)

470014

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

NAVMAN

FISH 4200 Installation and Operation Manual

Power and transducer connection

The FISH 4200 has two sockets located on the rear of

the unit. The power cable has a black 8 pin LT

connector plug. Push this plug into the lower socket,

which has a black nut and is located on the rear of the

display unit, then turn the collar to lock. Make sure

that the collar is secure for a watertight connection.

The transducer cable has a blue 8 pin LT connector

plug. Push this plug into the upper socket, which has

a blue nut and is located on the rear of the display

unit, then turn the collar to lock. Make sure that the

collar is secure for a watertight connection.

If the transducer is not connected, the message “NO

TRANSDUCER DETECTED. ENTER SIMULATION

MODE?” will appear. Press

to switch between YES

or NO. (More information on the simulation mode can

be found in the following section). Press

confirm the selection and the startup sequence will

continue. (Note: If the transducer was not intentionally

disconnected, turn the display unit off and refer to the

section on Troubleshooting in Appendix B.)

Names of keys:

Cursor key

key

gain key

Power key

Definition of Press and Hold in this manual:

· Press means to push the key for less than one

second.

· Hold means to push and hold the key down for

more than one second.

Power on

To turn the fishfinder on press .

Note: if the unit is wired for Auto Power (see section

5-4) the fishfinder will turn on automatically when

the boat's ignition is turned on.

A title screen briefly appears which displays basic

product information, including the software version.

The FISH 4200 then automatically displays the

screen that was last used.

Power off

To turn the fishfinder off, hold . A countdown box

appears. Continue to hold

for three seconds until

the fishfinder turns off.

Note: if the unit is wired for Auto Power (see

section 5-4) the fishfinder can only be turned off

when the boat’s ignition is turned off.

Language selection

To check which language is currently selected,

press

to display the MAIN MENU.

Follow these steps to change the language:

1. Power off the unit.

2. While the unit is off, hold down the

key.

3. Keep holding down the key and power

on the unit.

4. The screen displays a list of languages.

Press the Cursor or key to highlight a

language, then press the Cursor key to

select it. The fishfinder will continue the

startup sequence.

For further information, see section 4-8.

Backlighting

Use the button to adjust the backlighting to suit

individual preferences.

Press

once, at any time, to see the backlight

bar. This is displayed at the bottom of the screen

and shows the current setting.

Press

repeatedly until the desired backlighting

level is achieved. The backlight bar will disappear

2 seconds after the last press.

Fuel Computer

With an optional fuel kit the FISH 4200 becomes a

sophisticated yet easy to use fuel computer.

2 Getting started

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman FISH 4200 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info