663850
29
Zoom out
Zoom in
Vorherige Seite
1/34
Nächste Seite
G-PILOT 3100 Installation Manual
NAVMAN
29
Electrical
Heavy duty power supply 10.5 to 16.5 V
DC, 20 A maximum
Light duty power supply 10.5 to 16.5 V DC:
Main unit: 80 mA.
Each display unit, 30 mA without
backlighting, 110 mA with full
backlighting.
Other optional instruments: refer to the
instrument’s operation manual.
Interfaces
NavBus connection to other Navman
instruments.
NMEA 0183 outputs: HDG, HDT, RSA;
inputs APA, APB, BOD, BWC, MWD,
MWV, RMA, RMB, RMC, VHW, VTG,
XTE
NMEA 0183 ports:
NMEA 1: Input
NMEA 2: Can be programmed to be an
input or output
Standards compliance
EMC compliance
USA (FCC): Part 15 Class B.
Europe (CE): EN50081-1, EN50082-1
New Zealand and Australia (C Tick):
AS-NZS 3548.
Environment:
Compass, gyro, rudder feedback unit:
completely waterproof.
Display unit: IP66 from front when
correctly mounted.
Main unit: requires a cool, dry, clean
environment.
Appendix A - Speci cations
Main unit terminal block connections:
Terminal Signal
1 Heavy duty power positive, 10.5 to
16.5 V DC, 20 A maximum
2 Heavy duty power negative
3 Steering drive negative output
4 Steering drive positive output
Main unit connector connections:
Terminal Signal
1 Light duty power positive, 10.5 to
16.5 V DC, 80 mA maximum
2 Light duty power supply common
3 NavBus +
4 NavBus -
5 NMEA common
6 NMEA in 1
7 NMEA in 2
8 Steering clutch relay drive output,
switched ground to turn relay on,
30 V DC, 300 mA maximum
Display unit power/data cable wires:
Wire Signal
Red Power positive, 10.5 to 16.5 V DC,
30 mA without backlighting, 110
mA with full backlighting
Black Power negative
Orange NavBus +
Blue NavBus -
Yellow Factory use (isolate, do not cut)
White Factory use (isolate, do not cut)
Green External alarm, switched to
ground,
30 V DC and 250 mA max.
Appendix B - Alarm and warning messages
Alarm display Reason for message Recommended action by user Notes
BAT ALARM Battery voltage is less than the Check batteries a
minimum value set by the user Disengage G-PILOT if voltage too low
CAL ERROR
The G-PILOT rudder feedback unit
Calibrate both the units a
or compass unit is not calibrated (see sections 5-2 and 6-1)
CCH ERROR The clutch current is to high Check clutch connection a s
CE ALARM Course error has exceeded the Manually steer boat towards course a
maximum value set by the user
CSU ERROR Compass not sending data to Check compass is connected to a s
main unit main unit; Service compass
CUR ALARM The motor current exceeded the Check steering drive is not jammed a s
maximum value set by the user Increase the alarm value
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Navman G-PILOT 3100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Navman G-PILOT 3100

Navman G-PILOT 3100 Bedienungsanleitung - Deutsch - 33 seiten

Navman G-PILOT 3100 Installationsanweisung - Deutsch - 32 seiten

Navman G-PILOT 3100 Bedienungsanleitung - Englisch - 36 seiten

Navman G-PILOT 3100 Bedienungsanleitung - Holländisch - 34 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info