Bedienungsanleitung Navman M-Nav 950 (Seite 7 von 19) (Englisch)

663843

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Installing the M-Nav 900/950

Refer to the Garmin manual for instructions on assembling the

docking cradle and windscreen mount, and installing the unit in

the vehicle.

Attaching the Docking Cradle to the Windshield

NOTE

Some windshields contain areas of tinted glass that may inter-

fere with the GPS signal. Do not mount the M-Nav 900/950 in

these areas.

1. Connect the magnetic mount to the suction cup by firmly

pressing the socket on the mount of the ball on the suc-

tion cup arm.

2. Decide where to locate the suction mount on the wind-

shield. Use an alcohol swab to thoroughly clean that area

of the windshield, then dry the area with a soft, lint-free

cloth.

3. Press the suction cup firmly against the windshield for 3

seconds.

4. Push the lever down to vacuum-seal the suction cup to

the windshield.

Now you are ready to add the M-Nav 900/950 to the docking

cradle.

Adding the M-Nav 900/950 to the Docking Cradle

IMPORTANT

The M-Nav 900/950 must be in the docking cradle and con-

nected to the Qube tracking device in order for you to report

your driver status, send and receive messages, and oth-

erwise communicate with your fleet administrator through

the OnlineAVL2 application. The start-up screen will display

automatically.

The M-Nav 900/950 attaches magnetically to the cradle. Simply

align the unit with the cradle in the center of the back face and

when the M-Nav and cradle are close enough, the magnets will

snap the two together. The magnets are positioned to prevent

the M-Nav being attached in the wrong position. If you feel res-

istance, check that the cradle is correctly oriented (the word

“Garmin” should appear the right way up) and the M-Nav is in

landscape orientation (also with the word “Garmin” should

appear the right way up).

M-Nav 900/950 | User Guide

NOTE

The M-Nav 900/950 will charge only when connected to a

Qube tracking device in a standard vehicle installation, or

when using an AC adaptor supply. It will not charge effect-

ively when connected to a standard USB connection through

a PC or similar and powered on.

Getting Started

Disclaimer and Warning Screens

After a factory reset, you will be asked to accept the Garmin and

associated software end user license agreements. It is necessary

to scroll down to the bottom of the page before pressing Accept

All.

The "Warning" screen is displayed automatically. If you accept

the warnings, select Agree.

If your device is an M-Nav 950 (Garmin 670) you will be warned

about the navigation mode (truck vs. car) and offered the oppor-

tunity to switch mode. If you wish to use the truck-specific rout-

ing features, press Switch Mode and then select Truck/Lorry.

If the main menu is displayed, your M-Nav is ready to use. The

number of icons displayed in the main menu depends on the fea-

tures that have been enabled by your fleet administrator.

NOTE

If a different screen is displayed instead of the main menu,

see the next section.

Driver Log In & Status

The following screens will only be displayed if your fleet admin-

istrator has set up the Driver Login and Driver Status functions in

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman M-Nav 950 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info