Bedienungsanleitung Navman Multi 3100 (Seite 14 von 19) (Englisch)

512549

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

NAVMAN

MULTI 3100 Installation and Operation Manual

Power/data cables

Junction box

Power & data

connections

Power/data cable

NavBus cable

Group 1

Group 2

Power & data

connections

Away from engines, fluorescent lights,

power inverters and radio or radar

transmitters.

Accessable from behind; the minimum

clearance required at the back is 50 mm

(2") (see mounting diagram).

With the back of the unit protected from

moisture.

2 The unit must mount on a flat panel which is

less than 20 mm (0.75") thick. Stick the

mounting template in place. Drill a 50 mm (2")

fixing hole through the centre hole in the

template. Note that the template allows space

around the unit for the protective cover.

3 Remove the fixing nut from the back of the unit.

Insert the stud at the back of the unit through

the mounting hole. Hand tighten the fixing nut.

Transducers

1 If the MULTI 3100 does not come with

transducers, choose suitable transducers (see

section 9-3). If the MULTI 3100 is supplied with

transducers, see section 9-3 to ensure that

they are suitable.

2 Choose suitable locations for the transducers

and install them by following the instructions in

the Transducer Installation manual.

3 Fit the cables between the transducers and the

display unit:

Keep the cable away from other cables,

engines, fluorescent lights, power inverters

and radio or radar transmitters.

Do not lay the cable in the bilge.

If necessary, extend the cable by adding

extension cables.

Do not cut the cable on any depth

transducer.

Secure the cable at regular intervals.

4 Connect the transducers to the display unit

connectors.

Power/data wiring

1 Wire the display unit power/data cable:

The unit requires 12 V DC power. Fit a

power switch and fuse to the power supply

or power the unit from a fused auxiliary

switch. The fuse should be 1 A for up to

five instruments.

If the external beepers and lights require

more than 250 mA DC total, fit a relay.

A single unit can be wired as shown below:

With several instruments, use the optional

junction boxes to simplify wiring, as shown

below:

For information on how to connect NavBus

and to use junction boxes, refer to the NavBus

Installation and Operation manual.

2 Tape or cover any unused wires or connectors

to protect them from water and keep them from

shorting together.

10-2 Set up

1 Take the boat for a trial run to check that all

the instruments work correctly.

2 If the unit will take speed readings from a GPS

receiver, rather than a speed transducer or an

Black

12 V DC

power

Red

Switch

Fuse

External beepers or

lights (optional)

NMEA in (GPS, optional)

NMEA out (optional)

Depth transducer

White

Green

Yellow

Orange

Blue

Speed/temperature transducer

Cables Clearance

50 mm (2") minimum

20 mm (0.75")

maximum thickness

Fixing nut

Display

unit

Fixing hole

50 mm (2")

Side view of display unit mounting

NavBus (optional)

}

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Multi 3100 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Multi 3100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info