Bedienungsanleitung Navman Trackfish 6600 (Seite 17 von 83) (Englisch)

512557

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

TRACKFISH 6600 Installation and Operation Manual18

NAVMAN

3 Navigation: Chart

3-1 Introduction to navigating

The TRACKFISH has two ways of navigating,

going straight to a point or following a route.

Enter waypoints at points of interest before

starting to navigate (see section 5-2-1).

Tip: Create a waypoint at the start of the trip

to navigate back to.

Goto: Going straight to a point

The TRACKFISH can navigate straight to a

waypoint or to any arbitrary point:

1 Switch to the chart display

(see section 2-6).

2 Start navigating using the GOTO/AUTO

key (see section 3-4).

When the TRACKFISH is navigating, the

chart, data and highway displays show

navigation data. The chart shows:

The boat position .

The destination point marked with

a circle.

The boat’s plotted course to the

destination.

Two CDI lines, parallel to the boat’s

plotted course (see Appendix C, CDI).

If the TRACKFISH is connected to an

autopilot, the TRACKFISH will send data

to the autopilot to steer the boat to the

destination. Start the autopilot.

If the XTE alarm is enabled, an alarm will

sound if the boat deviates too much from

its intended course (to set the XTE alarm,

see section 15-8).

3 If the arrival radius alarm is enabled, then,

when the boat comes within the arrival

radius of the destination, an alarm will

sound to show that the boat has reached

the destination (to set the arrival radius

alarm, see section 15-8).

4 To stop the Goto, see section 3-4.

Following a route

A route is a list of waypoints that the boat can

follow (see section 6).

1 To create waypoints before creating the

route, see section 5-2-1.

2 To create a route, see section 6-2-1.

3 To start the route, see sections 3-4 or

6-3-1.

When the TRACKFISH is navigating,the

chart, data and highway displays show

navigation data. The chart shows:

The boat position .

The waypoint at the end of the current

leg marked with a circle.

The boat’s plotted course along the leg.

Two CDI lines, parallel to the boat’s

plotted course (see Appendix C, CDI).

If the TRACKFISH is connected to an

autopilot, the TRACKFISH will send data

to the autopilot to steer the boat to the

destination. Start the autopilot.

If the XTE alarm is enabled, an alarm will

sound if the boat deviates too much from

its intended course (see section 15-8).

If the arrival radius alarm is enabled, then,

when the boat comes within the arrival

radius of the waypoint at the end of the

current leg, an alarm will sound (to set the

arrival radius alarm, see section 15-8).

4 The TRACKFISH stops navigating to the

waypoint at the end of the current leg and

starts the next leg of the route:

a When the boat comes within 0.025 nm

of the waypoint.

b Or when the boat passes the

waypoint.

c Or if the waypoint is skipped (see

section 6-3-2).

5 When the boat has reached the ﬁ nal

waypoint, or to stop the boat following the

route at any time, cancel the route (see

section 6-3-3).

The chart display shows the chart, the boat’s position course and navigation data. To show the

Chart display, press ESC until the chart is displayed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Trackfish 6600 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Trackfish 6600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info