Bedienungsanleitung Navman TRACKFISH_6500 (Seite 8 von 88) (Englisch)

28502

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

TRACKFISH 6500 Installation and Operation Manual8

NAVMAN

1-3 Plug-in cards

The TRACKFISH can use two kinds of plug-in

card:

C-MAP™ chart cards have chart details

required for navigating in a particular

region. When a chart card is plugged in, the

extra details automatically appear on the

TRACKFISH chart display.

The TRACKFISH can use NT, NT+ and

NT-MAX cards. NT-MAX cards have much

more chart information than earlier cards,

including photos of points of interest.

C-MAP™ user cards are used to store

navigation data. Each user card expands

the TRACKFISH memory and allows

the data to be transferred to another

TRACKFISH easily (see section 14).

Note: The older 5 volt user cards are not

supported.

1-2 Cleaning and maintenance

The TRACKFISH screen is covered by a

proprietary anti-reflection coating. To avoid

damage, clean the screen only with a damp

cloth and mild detergent when dirty or covered

in sea salt. Avoid abrasive cleaners, petrol

or other solvents. If a plug-in card gets dirty

or wet, clean it with a damp cloth or mild

detergent.

Cover or remove a transom-mounted

transducer when repainting the hull. If painting

over a through hull transducer with antifouling

paint, use only one coat of paint. Remove the

previous coat of antifouling paint by sanding

it lightly.

To optimize performance, avoid walking on

or jamming cables and connectors. Keep the

transducer free of weed, paint and debris. Do

not use a high pressure water blast on a speed

sensor paddlewheel as it may damage the

bearings.

Push the dust cover over the display when the

TRACKFISH is turned off.

The NAVMAN TRACKFISH 6500 is a compact,

rugged, highly integrated marine chartplotter

and fishfinder. It is easy to use and has an easy

to read colour display. Complex functions can

be performed with a few key presses, taking

the hard work out of boating.

The available functions, displays and setup

menus depend on the optional sensors and

instruments that are installed:

Sonar functions require a sonar transducer

to be installed

Fuel functions require one or more

petrol/gasoline or diesel fuel sensors to be

installed.

SmartCraft engine functions require a

SmartCraft system to be installed. For

information on using SmartCraft, see

the SmartCraft Gateway Installation and

Operation Manual.

1-1 Overview

DSC/Buddy track functions require a

Navman DSC VHF radio with Buddy track

support to be installed.

The TRACKFISH can send data to other

instruments, such as an autopilot, and

receive data from other instruments.

For information on installing options, see

section 18-2.

This manual describes how to install and

operate the TRACKFISH. Special terms are

explained in Appendix C. For maximum

benefit, please read this manual carefully

before installing and using the unit. For more

information on this instrument and other

Navman products, go to our website, www.

navman.com.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman TRACKFISH_6500 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman TRACKFISH_6500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info