Bedienungsanleitung Nec GT 5000 (Seite 92 von 115) (Englisch)

493541

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

8-23

8. Using On-Screen Menu

Seamless Switch (GT6000 only)

1. What Does This Function Do?

This function provides a transition effect during source switch-

ing.

[Before switching]

[During switching]

[After switching]

* The drawings show an example of how “Effect-Wipe Right”

works.

• On/Off

Tur ns on or off the Seamless Switch function.

The default setting is “Off”.

• Effect

Selects one of the six effects during source switching.

The default setting is “None”.

2. Setting the Seamless Switch function.

2-1. Set effects and speed of the transition from source to source.

Select the Advanced Menu → [Projector Options] → [Seam-

less Switch].

None

Wipe Down

Wipe Left

Wipe Up

Wipe Right

Box In

Box Out

Displays a still image from the previously se-

lected source while switching to another source.

Displays a still image from the previously se-

lected source, then performs a wipe effect in a

desired direction while switching to another

source.

Displays a still image from the previously se-

lected source, then performs a “box in” effect

while switching to another source.

Displays a still image from the previously se-

lected source, then performs a “box out” effect

while switching to another source.

NOTE:

• With the Seamless Switch turned on, a signal with a higher resolution than

1024

768 (XGA) will be displayed using NEC’s Advanced AccuBlend technol-

ogy.

• When switching is performed using the Seamless Switch function between two

signals with different “Picture Management" settings, the hue of the image may

be changed immediately before source switching. This is because the Picture

Management settings will be changed along with source switching.

• Speed

Select one of the three switching speeds: Fast, Medium and Slow.

The default setting is “Medium”.

• Synchronize

The default setting is “Off”.

Auto

Off

Selecting "Off" can cause horizontal lines when a

moving image is displayed. If you want to delete

the lines, select "Auto". When "Auto" is selected,

the image can be distorted for a moment immedi-

ately after source switching.

Normally set to “Off”.

2-2. Set [Last Memory] or [Direct Key].

After turning on the Seamless Switch, be sure to do either

one of the following settings (1) or (2).

(1) Turn on “Last Memory” (Place a check mark in the “Last

Memory” check box.)

This setting enables the Seamless Switch function while

source is switching by using Source/Input (0-9) buttons on

the remote control.

(2) Register signals you want to use for the Seamless Switch

function in “Entry List”. In doing so, do the “Direct Key”

setting.

This setting enables the Seamless Switch function while

source is switching by using the CTL button and Source/

Input (0-9) buttons on the remote control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec GT 5000 Seite 92

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec GT 5000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info