Bedienungsanleitung Nec gt6000 (Seite 86 von 115) (Englisch)

216054

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

8-17

Enabling Last Memory [Last Memory]

The projector stores the last signal data in memory for each

input (RGB1, RGB2, DVI DIGITAL, Video, S-Video and Slot 1/

2).

This feature will reduce switching time between sources. If a

commercially available switcher is connected, turning on this

feature may cause the image to appear incorrectly.

Should this happen, turn this feature off to mute the screen

during switching.

Enabling Idle Mode [Idle Mode]

The projector has two standby modes: Standby and Idle.

Standby is the mode that allows you to put the projector in the

standby condition which consumes less power than the idle

mode. The projector is preset for Standby at the factory.

When this check box is turned on, you allow the RGB OUT

connector to output RGB signal during Idle mode.

NOTE:

* The RGB OUT connector will not output signal during the Standby mode.

*Via the USB interface the projector can be turned on from your PC using Dy-

namic Image Utility 2.0 during the Standby or Idle mode. On the LAN connection

the projector can be controlled or monitored from your PC using Dynamic Image

Utility 2.0 only in the Idle mode.

* The HTTP server functions are not available during Standby mode. See page 10-

11.

Tur ning on or off the Back Light [Back Light]

This function turns on or off the backlight of the buttons on the

cabinet.

NOTE: The Back Light feature is available in the normal operating mode or the idle

mode only.

Enabling Screen Trigger [Screen Trigger]

When "Screen Trigger" is selected and the projector is pow-

ered ON, the screen trigger output sends a low voltage trigger

to the screen controller and the screen will go down. When the

projector is powered OFF the screen trigger stops sending a

low voltage trigger to the screen controller and the screen will

go up. Use a commercially available stereo mini cable.

[Page 5]

Remote Sensor

This option determines which remote sensors on the projector

are enabled in wireless mode.

The options are: front, rear, right, or left. All checked boxes

indicate that they can accept the infrared signal from the sup-

plied remote control.

S-Video Mode Select:

This feature is used to select the S-Video signal detection mode.

This allows identifying of the S-Video signals with different as-

pect ratio (16:9 and 4:3).

Off ............... Does not identify any S-video signal.

S2 ................ Identifies the 16:9 or 4:3 signal.

NOTE: The Aspect Ratio is not available when S2 signal is detected.

Resetting the Filter Usage Hours [Clear Filter Usage Meter]

Resets the filter usage back to zero. Pressing this button ap-

pears a confirmation dialog box. To reset the filter usage hours,

press "OK".

[Page 6]

Selecting Communication Speed [Communication Speed]

This feature sets the baud rate of the PC CONTROL port (D-

Sub 9 Pin). It supports data rates from 4800 to 38400 bps.

The default is 38400 bps. Select the appropriate baud rate for

your equipment to be connected (depending on the equipment,

a lower baud rate may be recommended for long cable runs).

Enabling and Disabling Projector ID

Each projector needs its own unique addresses when used in

serial communication mode. You can choose one of 64 unique

address using the spin box. First select Enable. Keep pressing

̈ button increases the number. To make your setting avail-

able, select OK.

Selecting Default Source [Default Source Select]

You can set the projector to default to any one of its inputs

each time the projector is turned on.

Last ............. Sets the projector to default to the previous or

last active input each time the projector is turned

on.

Auto ............. Searches for an active source in order of RGB1

→ RGB2 → DVI(DIGITAL) → Video → S-Video

→ Viewer → Slot 1 → Slot 2 → RGB1(Video) →

RGB1(S-Video) → RGB1 and displays the first

found source.

Select .......... Displays the selected source input every time the

projector is started up. Select an input from the

pull-down menu.

8. Using On-Screen Menu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec gt6000 Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec gt6000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info