Bedienungsanleitung Nec gt6000 (Seite 87 von 115) (Englisch)

216054

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

8-18

Disabling the Cabinet Buttons [Control Panel Key Lock]

This option turns on or off the Control Panel Key Lock function.

NOTE:

* This Control Panel Key Lock does not affect the remote control functions.

* When the cabinet buttons are disabled, pressing and holding the CANCEL button

for about 10 seconds will change the setting to enable.

Lamp Settings

The projector is designed to accept two lamps (dual lamp sys-

tem). This dual lamp system provides prolonged lamp life or high

brightness or extra lamp (Extended life lamp).

NOTE: Be sure to use the same lamp type for both lamp 1 and 2.

Lamp Mode

This feature enables you to select two modes of the lamp:

Normal and Eco. The lamp life can be extended by using the

Eco mode.

Normal Mode . This is the default setting (100% Brightness).

Eco Mode ....Select this mode to increase the lamp life (80%

Brightness).

NOTE: When the optional Extended life lamp is used, the Lamp Mode is fixed to

Eco mode.

Lamp Select

This feature allows you to select which lamp to be used.

NOTE: This option is not displayed in the Basic menu.

* Changes to these options will not take effect for 90 seconds imme-

diately after the lamp is turned off (120 seconds for the extended

life lamp).

* The lamp cannot be turned off for 60 seconds immediately after

the lamp is turned on. Changes to these options cannot take effect

until then.

Dual ............. Select to use the two lamps at the same time to

increase brightness.

Lamp1/2 ...... Select to use one lamp of the two lamps. (Lamp

1 on the right side and Lamp 2 on the left side

when viewed from the front)

Interval

This allows you to specify the time for switching between the

two lamps alternately. This option is available only when

“Lamp1” or “Lamp2” is selected. When Auto is selected and

one lamp has reached the end of its usable life, the other lamp

is turned on. The lamp cannot be turned off for 60 seconds

immediately after the lamp is turned on.

NOTE: This option is not displayed in the Basic menu.

Lamp Type:

The lamp type you use and its information are displayed here.

The information displayed here are:

Light on or off, standard lamp or extended life lamp and re-

maining hours.

Link Mode

Settings

Selecting Standalone/Master/Slave

This feature is used for multiple projector connection. The

master projector is set to Master. The other slave projectors

are set to Slave. When not using Link mode, set to Standalone.

See page 7-5 for setting up for double stacking in link mode.

Selecting Communication Speed [Communication Speed]

This feature sets the baud rate of the PC CONTROL port (D-

Sub 9 Pin). This is the same procedure as in “Page 6” of “Setup”.

Enabling and Disabling Projector ID:

Each projector needs its own unique addresses when used in

serial communication mode. This is the same procedure as in

“Page 6” of “Setup”.

Copying Signals in the Entry List

Press the Entry List Copy button to copy all of the signals re-

corded in the Entry List from one projector to another.

8. Using On-Screen Menu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec gt6000 Seite 87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec gt6000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info