Bedienungsanleitung Nec MT1056 (Seite 3 von 55) (Englisch)

654050

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

E – 3

Important Safeguards

These safety instructions are to ensure the long life of your projector

and to prevent fire and shock. Please read them carefully and heed all

warnings.

Installation

1. For best results, use your projector in a darkened room.

2. Place the projector on a flat, level surface in a dry area away from

dust and moisture.

3. Do not place your projector in direct sunlight, near heaters or heat

radiating appliances.

4. Exposure to direct sunlight, smoke or steam can harm internal com-

ponents.

5. Handle your projector carefully. Dropping or jarring can damage in-

ternal components.

6. Do not place heavy objects on top of the projector.

7. If you wish to have the projector installed on the ceiling:

a. Do not attempt to install the projector yourself.

b. The projector must be installed by qualified technicians in order to ensure

proper operation and reduce the risk of bodily injury.

c. In addition, the ceiling must be strong enough to support the projector

and the installation must be in accordance with any local building codes.

d. Please consult your dealer for more information.

To Dealer or Installer:

To prevent the projector from falling, install it in a place and fasten it in

a way with sufficient strength to support the combined weight of the

projector (6.0 kg/13.3 lbs) and a ceiling mount for an extended period

of time as well as to withstand earthquakes.

Power Supply

1. The projector is designed to operate on a power supply of 100-120

or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this

requirement before attempting to use your projector.

2. Handle the power cable carefully and avoid excessive bending. A

damaged cord can cause electric shock or fire.

3. If the projector is not to be used for an extended period of time,

disconnect the plug from the power outlet.

Cleaning

1. Unplug the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily soiled,

use a mild detergent. Never use strong detergents or solvents such

as alcohol or thinner.

3. Use a blower or lens paper to clean the lens, and be careful not to

scratch or mar the lens.

CAUTION

Do not unplug the power cable from the wall outlet under any one

of the following circumstances. Doing so can cause damage to

the projector:

• While the Hour Glass icon appears.

• While the message “Please wait a moment.” appears. This message

will be displayed after the projector is turned off.

• Immediately after the power cable is plugged into the wall outlet (the

POWER indicator has not changed to a steady orange glow).

• Immediately after the cooling fan stops working (The cooling fan con-

tinues to work for ONE minute after the projector is turned off with the

POWER button).

• While the POWER and the STATUS indicators are alternately flashing.

Lamp Replacement

• To replace the lamp, follow all instructions provided on page E-47.

• Be sure to replace the lamp when the message “The Lamp has

reached the end of its usable life. Please replace the lamp.” ap-

pears. If you continue to use the lamp after the lamp has reached

the end of its usable life, the lamp bulb may shatter, and pieces of

glass may be scattered in the lamp case. Do not touch them as the

pieces of glass may cause injury. If this happens, contact your NEC

dealer for lamp replacement.

• Allow a minimum of ONE minute to elapse after turning off the pro-

jector. Then disconnect the power cable and allow 60 minutes to

cool the projector before replacing the lamp.

Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are unob-

structed to prevent the build-up of heat inside your projector. Allow

at least 3 inches (10 cm) of space between your projector and a

wall.

2. Prevent foreign objects such as paper clips and bits of paper from

falling into your projector. Do not attempt to retrieve any objects that

might fall into your projector. Do not insert any metal objects such as

a wire or screwdriver into your projector. If something should fall into

your projector, disconnect it immediately and have the object re-

moved by a qualified NEC service personnel.

3. Do not place any liquids on top of your projector.

• Do not look into the lens while the projector is on. Serious damage

to your eyes could result.

• Keep any items such as magnifying glass out of the light path of the

projector. The light being projected from the lens is extensive, there-

fore any kind of abnormal objects that can redirect light coming out

of the lens, can cause unpredictable outcome such as fire or injury

to the eyes.

• Do not cover the lens with the supplied lens cap or equivalent while

the projector is on. Doing so can lead to melting of the cap and

possibly burning your hands due to the heat emitted from the light

output.

CAUTION

Do not put the projector on its side when the lamp is turned on.

Doing so may cause damage to the projector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec MT1056 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec MT1056

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info