Bedienungsanleitung Nec MultiSync X551S (Seite 7 von 42) (Englisch)

493562

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English-5

English

This device cannot be used or installed without the Tabletop

Stand or other mounting accessory for support. For proper

installation it is strongly recommended to use a trained,

NEC authorized service person. Failure to follow NEC

standard mounting procedures could result in damage to the

equipment or injury to the user or installer. Product warranty

does not cover damage caused by improper installation.

Failure to follow these recommendations could result in

voiding the warranty.

Mounting

DO NOT mount the monitor yourself. Please ask dealer.

For proper installation it is strongly recommended to use

a trained, qualiﬁ ed technician. Please inspect the location

where the unit is to be mounted. Mounting on wall or ceiling

is the customer’s responsibility. Not all walls or ceilings are

capable of supporting the weight of the unit. Product warranty

does not cover damage caused by improper installation,

remodelling, or natural disasters. Failure to comply with these

recommendations could result in voiding the warranty.

DO NOT block ventilated openings with mounting

accessories or other accessories.

For NEC Qualiﬁ ed Personnel:

To ensure safe installation, use two or more brackets to

mount the unit. Mount the unit to at least two points on the

installation location.

Please note the following when mounting

on wall or ceiling

• When using mounting accessories other than those that

are NEC approved, they must comply with the VESA-

compatible (FDMlv1) mounting method.

• NEC strongly recommends

using size M6 screws

(11-12 mm + thickness

of bracket and washer in

length). If using screws

longer than 11-12 mm,

check the depth of the hole.

(Recommended Fasten

Force: 470 - 635N•cm)

NEC recommends mounting

interfaces that comply with

UL1678 standard in North

America.

• Prior to mounting, inspect the installation location to

insure that it is strong enough to support the weight of the

unit so that the unit will be safe from harm.

• Refer to the instructions included with the mounting

equipment for detailed information.

• Make sure there is no gap between the monitor and the

bracket.

Installation

Mounting

Bracket

Screw

Washer

Unit

11-12 mm

Thickness

of bracket

and washer

Screw length should equal

depth of hole (11-12 mm) + the

thickness of mounting bracket

and washer. Bracket hole

should be under φ 8.5 mm.

under

φ 8.5 mm

No gap

Using an optional wall mount (WM-46S-L/WM-46S-P)

• When using an optional wall mount (WM-46S-L/WM-

46S-P) or there is not enough room in back side, the

handles may need to be changed from normal to thin

position. See diagram below:

Screw position

change

Normal position

Thin position

• Stand holders may need to be taken out. See diagram

below:

Optional Stand holder

If mounting accessory is interfered with stand holder, it

may need to be taken out also.

Orientation

• When using the display in the portrait position, the

monitor should be rotated clockwise so that the left side

is moved to the top and the LED indicator light is on

the bottom. This will allow for proper ventilation and will

extend the lifetime of the monitor. Improper ventilation

may shorten the lifetime of the monitor.

LED Indicator

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec MultiSync X551S Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info