Bedienungsanleitung Nec VT45 (Seite 45 von 54) (Englisch)

488898

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

E–37

NOTE:The progress indicator shows the percentage of remain-

ing bulb life.The value informs you of the amount of lamp and

projector usage respectively.

To lock the cabinet buttons:

1) Use the Select

or button to select “Control Panel

Key Lock” and press the ENTER button. The submenu

will be displayed.

2) Use the Select

or button to select “Lock” and press

the ENTER button. The following confirmation screen

will be displayed.

3) Use the Select

or button to select “Yes” and press

the ENTER button.

The diplay will be changed to “Control Panel Key Lock -

Lock” and be returned to the previous menu screen.

NOTE: When “No” is selected and the ENTER button is

pressed, the displayed will not be changed and will be re-

turned to the previous menu screen.

To unlock the cabinet buttons:

1) Use the Select

or button on the remote control to

select “Control Panel Key Lock” and press the ENTER

button on the remote control. The submenu will be dis-

played.

2) Use the Select

or button on the remote control to

select “Unlock” and press the ENTER button on the re-

mote control. This change will take effect immediately.

NOTE:

• The confirmation screen will not be displayed.

• When the cabinet buttons are locked, pressing and hold-

ing the CANCEL button for about 10 seconds will change

the setting from Locked to Unlocked.

Resets the lamp clock back to zero. Selecting this option

displays submenu for a confirmation. To reset the lamp us-

age hour meter, use the

or button to select “Yes”.

NOTE: The projector will turn off and go into standby mode after

1100 hours (up to 1600 hours in Eco 1 mode / 2100 hours in Eco 2

mode) of service. If this happens, press the “Help” button on the

remote control for ten seconds to reset the lamp clock back to zero.

Do this only after replacing the lamp.

Resets the filter usage back to zero. Selecting this option

displays submenu for a confirmation. To reset the filter us-

age hour, use the

or button to select “Yes”.

Information

Displays the status of the current signal and lamp usage. This

dialog box has three pages. The information included are as fol-

lows:

[Page 1]

Source Index

Input Terminal

Horizontal Frequency

Vertical Frequency

Sync Polarity

[Page 2]

Signal Type

Video Type

Sync Type

Interlace

[Page 3]

Remaining Lamp Time (%)*

Lamp Hour Meter (H)

Projector Usage

Filter Usage

* When the remaining lamp time

reaches 0, the Remaining

Lamp Time bar indicator

changes from 0% to 100 Hours

and starts counting down.

If the remaining lamp time

reaches 0 hours, the projector

will not turn on regardless of

whether the lamp mode is set

to Normal or Eco.

Lock

Are you sure ?

Yes

Setup

Page1 Page2 Page3 Page4

Default Source Select

Communication Speed

Select

19200bps

Control Panel Key Lock

Clear Lamp Hour Meter

Clear Filter Usage

Default Source RGB

Unlock

Lock

Unlock

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec VT45 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info