Bedienungsanleitung Netgear R7800 - Nighthawk X4S (Seite 21 von 173) (Englisch)

670487

Zoom out

Zoom in

Vorherige Seite

1/173

Nächste Seite

The NETGEAR installation assistant runs on any device with a web browser. Installation and basic setup

takes about 15 minutes to complete.

To use the NETGEAR installation assistant to automatically set up your router on a network

with another router:

1. Turn the router on by pressing the On/Off button.

2. Make sure that your computer or WiFi device is connected to the router with an Ethernet cable (wired)

or over WiFi with the preset security settings listed on the label.

If you want to change the router’s WiFi settings, use a wired connection to avoid being

disconnected when the new WiFi settings take effect.

Note

3. Launch a web browser.

The page that displays depends on whether you accessed the router before or if the the router is

connected to another router or gateway:

• The first time you set up the Internet connection for your router, the browser goes to

http://www.routerlogin.net and the Configuring the Internet Connection page displays.

• If the NETGEAR installation assistant detects that the router is connected to another router or gateway,

you are prompted to set up the router in router mode or access point mode.

• If you already set up the Internet connection, enter http://www.routerlogin.net in the address field

for your browser to start the installation process.

4. Select the Help Me Choose radio button or Let Me Choose radio button:

• Help Me Choose. If you select this radio button, the NETGEAR installation assistant asks you a few

questions to determine if you should set the router in router mode or access point mode.We

recommend that you select the Help Me Choose radio button.

• Let Me Choose. If you select this radio button, you must select the Router Mode radio button or

the Access Point Mode radio button.You can change the mode by running the Setup Wizard again.

For more information, see Use the Internet Setup Wizard on page 24.

5. Follow the onscreen instructions.

The NETGEAR installation assistant guides you through connecting the router to the Internet.

6. If the browser does not display a router page, do the following:

• Make sure that the computer is connected to one of the LAN Ethernet ports or over WiFi to the router.

• Make sure that the router is receiving power and that its Power LED is lit.

• Close and reopen the browser or clear the browser cache.

• Browse to http://www.routerlogin.net.

• If the computer is set to a static or fixed IP address (this setting is uncommon), change it to obtain

an IP address automatically from the router.

7. If the router does not connect to the Internet, do the following:

a. Review your settings. Make sure that you selected the correct options and typed everything correctly.

b. Contact your ISP to verify that you are using the correct configuration information.

c. Read You Cannot Access the Internet on page 166. If problems persist, register your product and

contact NETGEAR technical support.

Connect to the Network and Access the Router

Nighthawk X4S AC2600 Smart WiFi Router

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear R7800 - Nighthawk X4S Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Netgear R7800 - Nighthawk X4S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info