Bedienungsanleitung Netgear WAC505 (Seite 33 von 149) (Englisch)

710463

Zoom out

Zoom in

Vorherige Seite

1/149

Nächste Seite

(Continued)

DescriptionSetting

By default, the VAP broadcasts its SSID so that WiFi clients can detect the SSID in their

scanned network lists.To turn off the SSID broadcast, select the No radio button.

Turning off the SSID broadcast provides additional WiFi security, but users must know

the SSID to be able to join the VAP.

If you set up a wireless distribution system (WDS; see Set Up a WiFi Bridge Between

Access Points on page 66), you must keep the SSID broadcast enabled.

Broadcast SSID

Select the 802.11K (RRM) check box to enable 802.11k Radio Resource Management

(RRM) so that the access point and 802.11k-aware clients can dynamically measure the

available radio resources. By default, RRM is disabled.

In an 802.11k-enabled network, access points and clients can send neighbor reports,

beacon reports, and link measurement reports to each other, allowing 802.11k-aware

clients to automatically select the best access point for initial connection or for roaming.

802.11K (RRM)

Select the Enable radio button to enable the access point to identify the WiFi devices

that are dual-band capable and steer those devices to the 5 GHz band rather than the

2.4 GHz band of the VAP. Generally, more channels and bandwidth are available in the

5 GHz band, causing less interference and allowing for a better user experience. By

default, band steering is disabled.

Band Steering

You can enter the minimum received signal strength indicator (RSSI) value in decibel

milliwatts (dBm) for a WiFi device to connect to the 2.4 GHz or 5 GHz radio on the access

point. If the RSSI value on the WiFi device is less than the configured RSSI value on the

access point, the WiFi device cannot connect to the access point.

Enter a value in the range of –100 to –10 dBm.The default is –100 dBm.

A higher value (for example, –10 dBm) indicates that the signal strength must be strong

for a WiFi device to be able to connect to the radio. A lower value (for example, –100 dBm)

indicates that the signal strength can be weak for a WiFi device to be able to connect to

the radio. However, a connection that is based on a weak signal can be unreliable.

For example, if the configured RSSI value on the access point is –70 dBm but the RSSI

value on the WiFi device is –75 dBm, the WiFi device cannot connect to the access point.

If the WiFi device is connected to the access point and then moves away from the access

point, causing its RSSI value to become too low, the WiFi device is disconnected from

the access point and an alarm is raised on the access point.

RSSI Threshold (-100 to

-10)

You can enter the VLAN ID that must be associated with the VAP. By default, the VLAN

ID is 1.

This VLAN ID is not the same as the 802.1Q VLAN ID that is used for the wired network

(see Set the 802.1Q VLAN and Management VLAN on page 90).

VLAN ID

Manage the Basic WiFi and Radio Features

Insight Managed Smart Cloud Wireless Access Point WAC505 User Manual

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear WAC505 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info