Bedienungsanleitung NetworX NX-584 HOME AUTOMATION MODULE (Seite 5 von 12) (Englisch)

629275

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

NX-584 Home Automation

VI. PROGRAMMING THE MODULE

A. USING THE LED KEYPAD

 To enter the Program Mode:

 Enter [r]-[8] (all of the function key LEDs will begin to flash).

 Enter the "Go To Program" code (default is [9]-[7]-[1]-[3]). If the code was valid, the

Service LED will flash, and the function LEDs will illuminate steady, indicating the device

to program should be entered.

 Enter the address of the NX-584, which is [7] [2] followed by [#]. At this point, the Armed LED

will illuminate while it is waiting for a programming location to be entered.

 Enter the desired programming location followed by the [#] key.

 The Armed LED will begin to flash while a programming location is being entered. If this

is a valid location, the Armed LED will extinguish, the Ready LED will illuminate, and the

binary data for the first segment of this location will be shown on the zone LEDS.

 If the desired location is the next sequential location, press the [POLICE] key.

 If the previous location is desired press the [FIRE] key.

 If the same location is desired press the [AUXILIARY] key.

 To change the data, enter the data followed by [r].

 The data will be entered, and the location will automatically increment to the next

segment. The data for that segment will be displayed. This procedure is repeated until

the last segment is reached.

 To exit this location without changing the data, press the [#] key.

 To review the data, repeat the above procedure, pressing the [r] key without entering data first.

Each time the [r] key is pressed, the next segment is displayed. After the last segment of a

location is programmed, pressing the [r] key will exit that location, turn the "Ready" LED off and

the "Armed" LED on. As before, you are now ready to enter another programming location. If an

attempt is made to program an invalid entry for a particular segment, the keypad sounder will

emit a triple error beep (beep, beep, beep) and remain in that segment awaiting a valid entry.

 To exit the Program Mode, press the [Exit] key to exit this programming level. Pressing the

[Exit] key again will exit the Program Mode.

B. U

SING THE LCD KEYPAD

All steps required for programming are the same as the aforementioned LED keypad. The LCD

keypad display will prompt you for the data required. While in the programming mode, and not in a

location, the number in parenthesis is the location you were previously changing. For example, if the

display reads "Enter location, then # (2)", it is reminding you that location 2 was the last location you

programmed. In feature selection data, the numbers of the enabled features will be displayed. The

features not enabled will display a hyphen (-).

VII. PROGRAMMING DATA

Programming data is always one of two types. One type of data is numerical, which can values from

0 -15 or 0-255 depending on the segment size. The other type of data, feature selection data, is used

to turn features on or off. Use the following procedures with these two data types:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NetworX NX-584 HOME AUTOMATION MODULE Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info