Bedienungsanleitung Nikon Laser 550A S (Seite 22 von 73) (Englisch, Französisch, Portugiesisch, Spanisch)

604470

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

Operational Summary

Caution—use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous radiation

exposure

1. Install a battery in the battery chamber. (See "Changing

Batteries")

2. Rubber eyepiece cup

Both eyeglass wearers and non-wearers can use this

rangefinder without attaching the rubber eyepiece cup.

3. Diopter adjustment

Adjust diopter to obtain a clear image in the LCD.

First, rotate the diopter adjustment ring counterclockwise

until it comes to a complete stop. Next, turn on the power

to activate the LCD when you look through the Nikon Laser

550A S. Rotate the diopter adjustment ring clockwise until

the display comes into focus.

If the diopter is not adjusted to correspond to your

eyesight, you may not be able to clearly focus your subject.

4. Measuring

Note: See the chapter "External and Internal display" for external

LCD panel.

Note: Depressing and holding down the POWER button causes

all symbols to be displayed in the internal LCD panel. After

you remove your finger from the POWER button, the last-

used setting is displayed. (If you briefly press the POWER

button then remove your finger, the LCD panel may

display the last-used setting without displaying all of the

symbols. This is not a malfunction or other problem.)

Before measuring, be sure to confirm settings, such as unit,

measurement/display mode and priority mode.

◎: See the relevant mode section in this manual for setting.

POWER

Set FULL/Limited

measurement mode

LCD is illuminated

Set your desired modes

◎

Align the reticle

with the target

POWER

appears

Results are converted

to the mode set and

displayed.

MODE

Indication

remains

illuminated for

30 sec.

30 seconds pass without operation ＊

Power off: LCD indications disappear

Measure again

Fail to measure

Cannot measure

Successfully

measured

For continuous distance

and angle measurement

(up to 20 seconds), keep

button depressed.

※

☆

☆【Continuous measurement mode】

Keeping the POWER button depressed allows you to

perform continuous measurement for 20 seconds.

Blinks while performing measurements.

When measuring a pin at a golf course, for example, use First

Target Priority and Continuous measurement mode for easy

measurement. With no objects between you and the pin, the

smallest number is the distance to your targeted pin.

※ See the the chapter "External and Internal display" for details

regarding the operations and results display of the various

modes.“

＊ Power turns off 30 seconds after the last operation.

5. Selecting display unit (Factory default setting is yard.)

1. Confirm the LCD panel is on.

2. Press and hold the

button for approx. two seconds.

3. When display unit has switched, release the

button.

4. After the unit is set, results will be converted and displayed in

the your selected measurement unit.

Meter

[ ]

Yard

[ ]

By pressing the MODE button, modes will change in the order

indicated above.

The angles and heights of two points are displayed only at the

full-mode setting.

Linear Distance [ ]

Horizontal Distance [ ]

Angle [ ]

Height [ ]

Vertical Separation

between 2 points

point

[ ]

1. Confirm the LCD panel is on.

2. Press

button within 0.5 seconds.

3. Release

button to switch the mode.

4. Repeat steps 2 and 3 until your desire mode is displayed.

5. Switching the mode after measurement converts the

results to the new mode.

6. After the mode is set, measurements are performed in the

new mode.

7. Switching Full/Limited modes (default setting is limited

mode)

1. Confirm the power is off (LCD is off).

2. Press and hold

button, then depress and hold

button within 0.5 second.

3. Continue to press and hold both buttons, (more than 2

seconds),to confirm the internal display is on.

When these buttons are pressed, all symbols are displayed .

6. Switching measurement/display modes (Factory default

setting is linear distance measurement mode)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nikon Laser 550A S Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info