Bedienungsanleitung Nilfisk-ALTO SC UNO 6 (Seite 10 von 19) (Englisch)

609299

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

10 Original Instructions

SC UNO/DUO

built up in the system. If a pressure is not being built up,

vent the machine as de scribed in section A.7 Venting.

SC DUO:

Position 1 = Pump no. 1 in operation

Position 2 = Pump no. 2 in operation

Positions 1+2 = Pumps no. 1 and 2 in operation

Turn the main switch (2) to position 1, 2 or 1+2. Push the

green starting button (3).

Check on the pressure gauge (5) that a pressure is being

built up in the system. If a pressure is not being built up,

vent the machine as de scribed in section A.7 Venting.

B.3 Operation - automatic start/stop

Always hold the spray lance with both hands!

The machine is automatically activated when the trigger

(1) of the spray handle is activated.

When the trigger is released, the machine automatically

stops after 20 seconds.

When the machine is not in use, the trigger should be

locked with locking device (see arrow).

The spray lance features 2 nozzles, a high pressure

nozzle and a low pressure nozz le.

B.4 FlexoPowerPlus and PowerSpeedVario

- pressure regulation

Turn the outermost part of the FlexoPowerPlus spray

lance:

- High pressure = MAX

- Low pressure = MIN./CHEM.

B.5

Double spray lance, pressure regulation

The spray lance features 2 nozzles - a high pressure

nozzle and a low pressure nozzle.

High pressure mode

When the pressure reducing valve (1) is completely clo-

sed (turned clockwise - B), only the high pressure nozzle

is used - high pressure mode.

Low pressure mode

When the reducing valve (1) is completely opened (turned

counterclockwise - A), both spray lances are used - low

pressure mode / possibility of dosing detergents.

The pres sure may be reg u lat ed between these positions.

B.6 Stop

Danger of scalding!

Never detach high pressure hoses at a water temperature

above 50°C.

Never detach the high pressue hose while the machine is

in operation.

1. To stop the machine, push the red stop button (4) and

turn the main switch (2) to position - 0 -.

SC UNO 5M-L - switch main switch to position - 0 -.

2. Close the shut-off cock of the water inlet and activate

the spray handle or open the high pressure cock to

relieve the pipeline / high pressure hose of pressure.

B.7 Frost protection

The machine should be installed in a frost-free room. This

applies to pump as well as pipelines incl. of outlet points.

Concerning outdoor outlet points it should be possible to

empty that part of the line which is exposed to frost.

IMPORTANT: For safety reasons, hoses, spray lances

and other accessories should always be thawed prior to

use.

C - Maintenance

It applies to the most exposed components that a mini-

mum of maintenance ensures a prolonged and prob lem-

free operation. Therefore it will be a good idea to make a

habit of the following:

Prior to attaching the water hose and the high pressure

hose, the quick couplings should be cleaned of dust and

sand.

Prior to attaching the spray lance or other accessories to

the spray handle, the machine should be started and the

quick coupling cleaned of dust and sand.

C.1 Oil

Check the oil level in the oil glas.

If the oil level gets too low, the machine will automatically

shut down. The red button will ﬂ ash (does not apply to

SC UNO 5M-L).

In the case of repeated low oil level (oil waste) please

contact a Nilﬁ sk service technician.

PROTECT THE ENVIRONMENT

Waste oil and oil sludge must be removed as laid down in

the instructions.

C.2 Water ﬁ lter

To avoid debris entering the high pressure pump, a water

ﬁ lter (ﬁ ne) is ﬁ tted at the wa ter inlet. Dependent on the

purity of the water, this ﬁ l ter will have to be cleaned at

regular in ter vals.

The ﬁ lter can be removed when the quick coupling (pos.

1) has been un screwed.

C.3 Cleaning of high pressure nozzle

A clogging up in the nozzle causes a pump pressure

which is too high, and a cleaning is immediately required.

1. Stop the cleaner and detach the spray lance.

2. Clean the nozzle.

IMPORTANT: ONLY use the cleaning tool when the

spray lance is detached.

3. Flush the spray lance backwards with water.

4. If the pressure is still too high, repeat items 1-3.

C.4 Disposable waste

This high pressure washer consists of parts which can

affect the invironment when thrown away. Parts that can

pollute are as follows:

Oil, painted/zinc-coated parts, plastics/plastic-coated

parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk-ALTO SC UNO 6 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk-ALTO SC UNO 6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info