609299
11
Zoom out
Zoom in
Vorherige Seite
1/19
Nächste Seite
11Original Instructions
EN
SC UNO/DUO
Therefore, it is important to follow the laws concerning the
removal of polluting and dangerous materials when repla-
cing spare parts or disposing of high pressure washer.
It is recommended that you bring the rejected parts to wa-
ste disposal areas or recycling plants that are approved
for the destruction of these types of materials.
Troubleshooting
You have chosen the best quality and therefore deserve the best service. To avoid unnecessary dis ap point ments, you
should check the following before contacting the nearest Nil sk service organisation:
Symptom Reason Action
Machine/pump will not start > A fuse has blown
> Power/plug not connected
> Thermal switches in motor activated
(red lamp ashes)
> Thermal relay switched off (red lamp
ashes)
> Oil shortage in pump
Change the fuse.
• Connect power/plug.
Let the motor cool. Start the machine
and check that the working pressure
is not too high and that the mains
voltage corresponds to the speci ca-
tions.
• Re ll with oil.
Fuses blow > Installation does not correspond to
the ampere consumption of the ma-
chine
Change to an installation correspon-
ding to the ampere consumption of
the machine at a minimum. Replace
the fuse.
Working pressure too low > Nozzle worn
> Wrong spray lance
> Reduction valve of spray lance not
adjusted to max. pressure.
> Nozzle partly clogged up
Replace the nozzle.
Replace the spray lance (see section
B4/B5).
Turn reduction valve completely
counter-clockwise.
Clean the nozzle (see section C.3).
Working pressure not steady > Water temperature too high
> Insuf cient water supply
> High pressure hoses too long
> Air in the system
> Water inlet lter clogged up
Lower the temperature of the inlet
water to max. temperature (see
Technical Speci cations).
Check water inlet lter. If that does
not solve the problem, the water
supply for the machine is insuf cient.
NB! Avoid long, thin hoses (min.
3/4").
Dismount high pressure extension
hoses and retry.
Extension hose max. 50 m.
NB! Avoid long extension hoses with
many couplings.
Vent the system (see section A.7).
• Clean lter (see sect. D.2)
No working pressure > Nozzle clogged up
> No inlet water
> High pressure cock of outlet point
open.
Clean nozzle (see sect. D.3)
Check that the shut off cock of the
water inlet is open. Check that the
water supply meets the requirements
(see section A.4)
Close all high pressure cocks not in
use.
Machine starts and stops > Leaky hose/ pipeline/spray handle Repair leak.
Machine stops > Oil shortage in pump. Red lamp
ashes
Top up with oil
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Nilfisk-ALTO SC UNO 6 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Nilfisk-ALTO SC UNO 6

Nilfisk-ALTO SC UNO 6 Bedienungsanleitung - Deutsch - 19 seiten

Nilfisk-ALTO SC UNO 6 Bedienungsanleitung - Holländisch - 19 seiten

Nilfisk-ALTO SC UNO 6 Bedienungsanleitung - Französisch - 19 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info