Bedienungsanleitung Nilfisk CDF 2000 (Seite 24 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

73357

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Instructions for use

Before using the vacuum cleaner make sure that the voltage shown

on the rating plate at the backside of the motor top of the vacuum

cleaner, corresponds with the mains voltage.

The vacuum cleaner is supplied with a paper dust bag already in

place. Never use the vacuum cleaner without a properly fitted dust

bag and main filter. The procedure for replacing the dust bag is

described under point 7.

IMPORTANT WARNINGS

1. This machine is not suitable for picking up health endangering

dust.

2. This machine is for dry use only and shall not be used or

stored outdoors in wet conditions. Store indoors between max.

40°C (degrees centigrade) and min. 0°C (degrees centigrade).

3. The machine for vacuum dry dust must not be used for the

suction of water or other liquids.

4. The machine must not be used for picking up combustible

or explosive materials, nor should it be used in an explo sive

atmosphere.

5. Under no circumstances should the machine be used for picking

up hot material. In particular the machine must not be used for

cleaning open and closed fireplaces, ovens or similar that

contain warm or glowing ashes.

6. The machine must not be used if the electrical cord

shows any sign of damage. Regularly inspect the cord for

damage, in particular if it has been crushed, shut in a door or

run over.

7. The machine must not be used if it is faulty.

8. Do not unplug by pulling on cord. To unplug, grasp the plug,

not the cord.

9. When repairing or replacing the cord, the same type of cord as

originally supplied with the machine must be used. This cord

can be supplied by NILFISK.

10. The plug must always be removed from the socket outlet before

starting any service work of the machine or the cord.

11. Repair of the electrical unit with motor or the cord must

only be carried out by a skilled or instructed person after having

disconnected the main switch installed prior to the machine or

after having removed the plug from the current socket.

12. No changes or modifications to the mechanical or elec trical

safety devices should be made.

13. The maximum airborne noise (sound pressure level) is below 7

0 dB(A)/20µPa.

14. The appliance is not intended for use by young children

or infirm persons without supervision. Young children

should be supervised to ensure that they do not play with

the appliance.

This appliance conforms with EC Directive 89/336/EEC,

EEC, 73/23/EEC, 93/68/EEC.

1. Starting/stopping

Unwind all the cord and place the appliance plug into the wall

socket.

-On: Press button 1 to start the vacuum cleaner.

-Off: Press button 1 once more to stop the vacuum cleaner.

After cleaning grasp the plug and unplug the cord from the wall

socket. Roll up the cord loosely around the handle and park or store

the vacuum cleaner.

Note

Do not roll the cord tightly around the handle as this will place a

strain on the cord and considerably shorten its life.

Models with two speed regulation

The motor has two power settings - high power and low power.

The motor will start under whatever power setting was in effect the

last time the vacuum cleaner was in use.

You can cycle between high power and low power by repeatedly

pressing button ll.

2. Hose and tube connection

Insert the hose connection into the suction inlet and turn it clockwise

to lock it. Reverse this procedure to disconnect the hose.

Assemble the hose with the tube and nozzle by pressing the parts

together.

Models with telescopic tube

The telescopic tube can be adjusted to suit your height. Hold with

one hand on the larger tube and push the button on it and with the

other hand pull or push the smaller tube to the wanted length.

3. Changing the dust bag /

Exhaust filter

The dust bag must be changed when the suction efficiency is falling.

1. Open the container by pushing the knob on the lock.

2. Remove the upper housing.

3. Release the hose connection from the suction inlet by twisting

it counter-clockwise and remove it. Remove the used dust bag

by pulling in the card board flap and seal it. Dispose it in a

safe manner.

4. Insert the new dust bag by guiding the cardboard into the hooks

inside the dust bag housing and push it down. Unfold the new

dust bag carefully. Insert the hose connection into the dust bag

housing and twist it counter-clockwise to lock it.

5. Replace the guide pin of the upper housing into the guide hole

of the dust bag housing and close the container parts.

6. Close the lock.

Note

The suction efficiency of the vacuum cleaner depends on the size

and quality of the dust bag. Use original Nilfisk bags only.

If any bags, other than original Nilfisk bags are used, the airflow

may be restricted, resulting in the motor overheating and subsequent

damage.

Damage resulting from use of the vacuum cleaner without or with

other than the original Nilfisk bags, is not covered by the guarantee.

Replacing the exhaust filter (model CDF 2000,

CDF 2010)

The exhaust filter placed under the handle cover attracts and retains

micro-particles efficiently. This filter should be replaced every time

you open a new box with five dust bags.

1. Push the button inside the handle upwards and twist the handle

counter-clockwise and remove it.

2. Remove the sound suppressor material with the exhaust filter

material.

3. Replace with the new exhaust filter material and position the

sound suppressor material over it as shown.

(It must not crumple up)

4. Locate the handle into position and lock it by turning it

clockwise until it snaps.

ENGLISH

Nilfisk CDF 2000 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info