Bedienungsanleitung Nilfisk CDF 2000 (Seite 26 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

73357

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Important warnings (Electro Nozzle 2832)

Before using the appliance make sure that the voltage shown on the

rating plate corresponds with the mains voltage.

The appliance must not be used for picking up hazardous material

- i.e. toxic dust, combustible or explosive material, nor should it be

used in a explosive atmosphere.

Under no circumstances should the appliance be used for picking

up hot material. In particular the appliance must not be used for

cleaning open and closed fireplaces, ovens or similar that contains

warm or glowing ashes.

Avoid vacuuming hard, pointed objects, since they may damage

your appliance.

The appliance must not be used for the suction of water, liquids or

inflammable gasses.

Carpets that have been shampooed should only be vacuumed when

they have completely dried out, since your appliance may otherwise

be damaged.

The appliance must not be used if the electrical cable or plug show

any sign of damage. Regularly inspect the cable and the plug for

damage. If it becomes damaged, it should be repaired only by

Nilfisk-Advance or an Authorised Nilfisk Service Dealer. Do not

handle the electrical cable or plug with wet hands. Do not unplug by

pulling on cable. To unplug, grasp the plug, not the cable.

The plug must always be removed from the socket outlet before

starting any service or repair work of the machine or the cable.

Avoid running over the flex with the appliance. Never touch

the brush with your fingers while it is running. No changes or

modifications to the mechanical, electrical or thermal safety devices

should be made.

The maximum airborne noise (sound pressure level) is below 70

dB(A)/20µPa.

This appliance complies with the following EC Directives: 73/23/

EEC (including Amendment 93/68/EEC),

Low-Voltage Directive - 89/336/EEC (including Amendment 92/31/

EEC and 93/68/EEC), EMC Directive.

Instructions for use

Press the cable into the clamps and clip on to the suction head and

tube, running the flex under the handle.

Plug the appliance into the plug socked.

The cleaning head automatically swithces on when the vacuum

cleaner is started.

Remove larger debris, such as scraps of fabric, paper, etc. from the

floor to avoid the roller being clogged. The appliance is suitable for

carpets and hard floors.

Do not use this appliance on carpets with very long fringes or piles

deeper than 15 mm. The pivoted joint of the nozzle enables the

nozzle to be easily steered in every direction.

If the appliance stops:

If the motor of the appliance is overloaded, e.g. because the brush

roller is jammed by the intake of bulky foreign bodies or carpet

threads, the overheating trip will switch off the motor.

Switch off the vacuum cleaner, unplug it, allow the motor of the

appliance to cool down and clean the brush roller as described under

“Cleaning and care”, if necessary. The appliance can be switched on

again after about 2 minutes.

Cleaning and care

Switch off and unplug the appliance

Never immerse the appliance in water or other liquids while

vacuuming.

Cleaning the roller:

Remove any hairs and threads that have accumulated around the

rollers simply by cutting them with scissors and pulling off (fig. 2).

Dismantling the cleaning roller:

Loosen the engagement hooks with a screwdriver (fig. 3). Lift the

cover forward.

Turn over the electric cleaning head and detach the housing cover

(fig. 5). Dismantle the cleaning head roller. Pull off and clean the

roller bearings. When assembling the cleaning head roller, make sure

that the tooth system of the toothed belt coincides with the pinions.

Fit the cover on the appliance and engage by uniform pressing from

above.

Cleaning the rollers:

If the rollers start to seize up : Remove any hairs and threads that

have accumulated around the roller axles. The roller can be removed

for cleaning. The roller can be simply levered out of their location

using a firm object (e.g. a screwdriver) (please observe the arrow

direction).

Insert the screwdriver as illustrated (fig. 4) in the oblique location

and lever out the roller. Remove hairs and threads. Refit the roller,

making sure that the axles are engaged on both sides!

Caution:

Place the flat of the hand over the roller when levering out. This

avoids the roller springing out.

Important

If the nozzle is hard to slide:

Reduce the power of the appliance. The cleaning action is then not

impaired.

To detach

Unplug the appliance, detach the cable clamps, and remove the

electric cleaning head by pulling and twisting.

Specifications

Model 2832

Rated power (W) 30

Protection grade (moist., dust) IP40

Protection class (electrical)

Brush rotating speed (rpm) 3350

(hard floor)

Specifications and details are subject to change without prior notice

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk CDF 2000 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info