801551
23
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
21
The vibration setting is restored to the final saved
setting when the device is turned off and on again. This
setting is common in all modes; change made in any
mode also applies to the other modes.
Brightness
It enables you to adjust the display and keypad
backlight level according to your personal preference. It
works in 2 different ways: Continuously or automatically
meaning the backlight lights up only for a short period
of time when a target is detected or while navigating
the menu and then it goes off. The default setting is
automatic.
To adjust the Brightness, use the plus (+) and minus
(-) buttons. The dotted boxes indicate the automatic
backlight level and the solid ones indicate the continuous
backlight level. To switch from automatic to continuous,
keep pressing the plus (+) or the minus (-) button. When
the box is not selected, it means that the backlight is
off. The continuous operation of the backlight will affect
power consumption, which is not recommended.
4
99
The backlight setting is restored to the final saved
setting when the device is turned off and on again. This
setting is common in all modes; change made in any
mode also applies to the other modes.
LED Flashlight
It is the headlight used for lighting the area you are
scanning while detecting at night or in dark locations.
To turn on or off the LED Flashlight, after selecting it
in the settings menu, use the plus (+) and minus (-)
buttons.
4
99
The LED Flashlight will always revert back to off
position when the device is turned off and on again.
This setting is common in all modes; change made in
any mode also applies to the other modes.
LED Flashlight does not operate when the device is off.
It is recommended to turn it on only when necessary
since its operation consumes extra battery power.
Save and Factory Defaults
SIMPLEX will save all settings automatically once you
turn your detector off and on again except for the ones
listed below:
Ground Balance, Iron Off, Ground Suppressor, Frequency
Shift and LED Flashlight.
To revert back to factory defaults, press the plus (+) or
the minus (-) button once. After hearing 3 beeps, the
device will revert back to factory defaults and go back
to the main screen.
4
99
23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Nokta Simplex LITE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Nokta Simplex LITE

Nokta Simplex LITE Bedienungsanleitung - Türkisch - 32 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info