Bedienungsanleitung Nokta Simplex LITE (Seite 24 von 32) (Englisch)

801551

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

SETTINGS FOR ULTRA VERSION ONLY

Coin/Relic ID Scale

By using this feature, you can differentiate the Target

ID scale according to the type of target you’re looking

for. If you are a coin hunter, using the Coin ID Scale and

if you are a relic hunter, using the Relic ID Scale will

enable you get more stable IDs. The default one is the

Coin ID Scale.

In the coin option, the ferrous ID range is 01-14 and

in the relic one it is 01-39. In other words, when the

Coin ID Scale is selected, the device will produce

a ferrous tone for targets with 0-14 IDs and a non-

ferrous tone for those with 15-99 IDs. When Relic ID

Scale is selected, the device will produce a ferrous tone

for targets with 01-39 IDs and a non-ferrous tone for

those with 40-99 IDs.

Keep in mind that the ID will differ for the same target

between these 2 options!

To use this setting, after pressing the Power & Settings

button to go into settings, use the right and left buttons

to select the Discrimination setting. Press the Ground

Balance / Confirm button to access the upper settings.

Using the right and left buttons, select the Coin/Relic ID

Scale setting which is the third setting. You can switch

between the two options using the plus (+) and minus

(-) buttons.

This setting is restored to the final saved setting when

the device is turned off and on again. This setting is

common in all modes; change made in any mode also

applies to the other modes.

Target ID Depth

Adjusts the depth level that the device displays an ID

for a detected target. It consists of 3 levels: L (Low), M

(Medium), H (High). Factory default is set to ‘’M’’. The

lower the ID depth level is, the higher the ID accuracy

and vice versa. At the high level, the IDs may become

jumpy.

To use this setting, after pressing the Power & Settings

button to go into settings, use the right and left buttons

to select the Discrimination setting. Press the Ground

Balance / Confirm button to access the upper settings.

Using the right and left buttons, select the Target ID

Depth setting which is the fourth setting. You can

adjust the ID depth level using the plus (+) and minus

(-) buttons.

This setting cannot be used in the All Metal mode and

thus cannot be selected.

Recovery Speed

The Recovery Speed setting adjusts the speed of target

response. It allows for separation between multiple

targets in close proximity. Recovery Speed setting

enables you to detect smaller targets among trash or

ferrous targets. This setting can be adjusted between 1

and 5 with 1 being the slowest and 5 being the fastest.

Recovery Speed setting only affects the mode currently

selected; changes made in one mode do not affect the

others. When the Recovery Speed setting is set to a

low number, the ability of the device to detect targets

in close proximity decreases but its depth increases.

Similarly, a high Recovery Speed setting (for example 5)

will increase the ability of the device to detect targets

in close proximity but will decrease the depth. It is

recommended that you practice with different metals

placed close to each other before starting to use this

setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nokta Simplex LITE Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nokta Simplex LITE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info