Bedienungsanleitung NordicTrack C 2000 - NETL12807.2 (Seite 14 von 32) (Englisch)

605362

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to

old temperatures, allow it to warm to room tem-

perature before turning on the power. If you do not

o this, the console displays or other electrical

components may become damaged.

Plug in the power cord

(see page 12). Next, lo-

cate the reset/off circuit

breaker on the treadmill

frame near the power

cord. Switch the circuit

breaker to the reset position.

IMPORTANT: The console features a display demo

mode, designed to be used if the treadmill is dis-

played in a store. If the displays light as soon as

you plug in the power cord and switch the circuit

breaker to the reset position, the demo mode is

turned on. To turn off the demo mode, hold down

the Stop button for a few seconds. If the displays

remain lit, see THE INFORMATION MODE on page

19 to turn off the demo mode.

Next, stand on the foot

rails of the treadmill. Find

the clip attached to the key

(see the drawing to the

right) and slide the clip

onto the waistband of your

clothes. Then, insert the

key into the console. After

a moment, the displays will light. IMPORTANT: In an

emergency situation, the key can be pulled from

the console, causing the walking belt to slow to a

stop. Test the clip by carefully taking a few steps

backward; if the key is not pulled from the console,

adjust the position of the clip.

HOW TO USE THE MANUAL MODE

1. Insert the key into the console.

See HOW TO TURN ON THE POWER to the left.

2. Select the manual mode.

When the key is

inserted, the

manual mode

will be selected.

If a workout has

been selected,

reselect the

manual mode by removing the key and then rein-

serting it.

3. Start the walking belt.

To start the walking belt, press the Start button, the

Speed increase button, or one of the speed but-

tons numbered 2 through 20.

If you press the Start button or the Speed increase

button, the walking belt will begin to move at 2

Km/H. As you exercise, change the speed of the

walking belt as desired by pressing the Speed in-

crease and decrease buttons. Each time you press

the Speed increase or decrease button, the speed

setting will change by 0.1 Km/H; if you hold down a

button, the speed setting will change in increments

of 0.5 Km/H. Note: After you press the buttons, it

may take a moment for the walking belt to reach

the selected speed setting.

If you press one of the speed buttons numbered 2

through 20, the walking belt will gradually increase

in speed until it reaches the selected speed setting.

To stop the walking belt, press the Stop button. To

restart the walking belt, press the Start button, the

Speed increase button, or one of the numbered

speed buttons.

Reset

Position

Clip

Key

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NordicTrack C 2000 - NETL12807.2 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NordicTrack C 2000 - NETL12807.2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info