709180
9
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
GB
Connecting the SOLAR-HOME-STATION Deleting all the programmed-in hand
AKKU-POWER-SYSTEM
Connecting plan (4) transmitter codes
Important instructions: - Press the “PRG” button on the SOLAR-HOME-
230V power supply for garage door operators with
- When connecting accumulators and charger STATION and keep it pressed for approx. 10
SOLAR-HOME-STATION SHS200
modules, it is important to observe the correct seconds until the LED starts flickering and then
polarity (fire hazard). goes out
Suitable for:
- When using operators with a protective
conductor connection, the SOLAR-HOME- Setting the operator
Novoferm
STATION must be properly earthed. To set the garage door operator, press the
NovoPort, Novomatic 403 / 553 / 553S and
- Follow all the instructions provided in the appropriate button on the hand transmitter. The
Novodoor
SOLAR-HOME-STATION'S Instruction Manual. SOLAR-HOME-STATION switches the 230V power
- Insert the operator's mains plug into the SOLAR- supply on. Program the operator in accordance
Siebau
HOME-STATION'S electric socket (4c). with the Operating and Installation Instructions.
ATS24, TYPE 403, TYPE 553, TYPE 553S,
- Connect the accumulator pack to the “AKKU”
TYPE 611
input of the SOLAR-HOME-STATION (4d). Attention: after 60 seconds the SOLAR-HOME-
- Do not connect the start cable until you have STATION automatically switches off the 230V
and
programmed the operator for operation of the power supply. Throughout programming, you
garage door (see point 5). The “START” output should therefore operate the hand transmitter
tormatic
on the SOLAR-HOME-STATION is connected to every 30 seconds to maintain the 230V power
GTA 601, GTA 602, GTA 611, GTA 612, GTA 701,
the “START“ input on the garage door operator supply until the process has been completed.
GTA 702, GTA 801 and GTA 802
using a two-core lead (4a, 4b and 4d).
- Connect the solar module (optional) to the Do not connect the start cable until all the
Becker / Rollmatic BV
“MODUL” input on the SOLAR-HOME- necessary settings have been made.
BOM 520, BOM 820
STATION.
Operation
If using operators of other makes, the switch-on
Use the hand transmitter to open and close the
behaviour can lead to malfunctions. Putting into service
door.
The SOLAR-HOME-STATION first switches on the
Charger For the remote control use a free channel on the
230V power supply.
Before being used for the first time, the hand transmitter. If no free channel is available,
After 2 ½ seconds, the station sends a start
accumulator pack must be charged. To do this, delete the transmitter that has been tuned into the
impulse to the operator.
connect the accumulator pack to the charger (1a). operator.
The door automatically travels to the end-of-travel
Plug the charger into the electric socket and set
position.
the slide switch to 12V (1b). The accumulator is Tuning the hand transmitter into the
After 60 seconds, the SOLAR-HOME-STATION
fully charged when the green light comes on. SOLAR-HOME-STATION
switches the 230V-power supply off again. The
Max. charging time 24 hours. - Press the PRG button on the SOLAR-HOME-
light on the operator goes out.
After charging, disconnect the charging cable STATION.
again (1c). - The LED on the SOLAR-HOME-STATION
Changing the accumulator:
flashes.
We recommend that you buy an additional
Installing the SOLAR-HOME-STATION and - Press one of the buttons on the hand transmitter
accumulator pack so that while one accumulator
the wall holder for the accumulator pack and keep it pressed.
pack is in operation, the other can be recharging.
Install the SOLAR-HOME-STATION within - As soon as the LED on the SOLAR-HOME-
accessible range of the operator's mains cable (0). STATION flashes rapidly, the hand transmitter
Change the accumulator as explained in 3a, 3b.
To do so, hold the station against the wall and has been tuned in.
Charge the accumulator pack as shown in section
mark the drill holes. Fix in place using suitable
1.
screws and wall plugs (2). Repeat the process for any further hand
Affix the wall holder for the accumulator pack transmitters. Up to 60 codes can be programmed
within accessible range of the SOLAR-HOME- in.
STATION using suitable screws and wall plugs (2).
1
2
4
5
Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Novoferm APS 230 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Novoferm APS 230

Novoferm APS 230 Zusatzinformation - Alle Sprachen - 1 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info