Vivoport
®
Installation Instructions
only to be used as complement to the installation instructions for hand
operated doors
- Installation only by qualified fitters -
Please read carefully prior to installation
Number combinations in square brackets, e.g. [1.05 a], refer to the corr
ding page and illustration in the illustration section.
The following points that differ from the installation instructions for hand opera-
ted doors have to be taken into account:
1 Remove protection foil and place door in or behind the opening [3.05 a]
2 T
aside. Remove mould side part.
3 Carry out instructions in points 2 – 7 analogous to the installation instructions for
hand operated doors.
4 Clip in plastic bearing bushes in the roller block [3.05 b, c]. If necessary loosen rol-
ler block screw connection [3.05 d]
5 Carry out instructions in points 8 – 10 analogous to the installation instructions for
hand operated doors.
6 Screw on lock [3.10 a] and insert rubber buffer into the track [3.10 b] so that the
upper snapper does not later touch the track connector in the open end position.
7 Carry out instructions in points 11 – 18 analogous to the installation instructions
for hand operated doors.
8 Hang the emergency unlocking in the operator [3.10 c]. Drill a 2mm hole in the in-
side handle [3.10 d] and pass through the wire cable. Secur
emergency unlocking function. Attention! Wir
tension.
9 Screw transformer mounting (accumulator mounting) in the middle to one of the
tracks (electrical socket side) [3.15 a,b].
10 Lay spiral cable along the door leaf by means of spring clips [3.15 c,d]. Fix to the
roller block as well.
11 Insert connector into the operator housing [3.15 e] and insert mains plug into the
electrical socket.
Programming instructions:
Log on the transmitter:
12 After the first switch-on one device must initially be logged on:
12.a Press the blue pushbutton on the bottom of the operator and keep pressed
until after about.4 seconds a short acknowledgement tone is heard, then re-
lease the button.
12.b The light starts to flash
12.c
logged on by pressing one of its pushbuttons. The operator acknowledges
the successful log-on by an acknowledgement tone. Up to 4 hand-held
transmitters can be logged on. If an attempt is made to log on a fifth hand-
held transmitter the operator will ignore it.
Set soft-stop, begin reference run
T
measured and recor
reaching the respective end position.
13 Close the door so that the operator opens the door for the next run
14 Keep the pushbutton on the operator pressed until after approx. 4 seconds a short
beep tone acknowledges the long press of the pushbutton, then release the pus-
hbutton
15 The light starts to flash
16 Press the pushbutton on the operator once more shortly
17 The lamp flashes no more (the run times have been deleted – the next open run
and the next close run will be a reference run)
18 Press the pushbutton on the operator or the hand-held transmitter to start the r
ference run “open”
19 The door opens
20 When the door is fully opened the operator stops and acknowledges the refer
run “open” with a short flash of the light
21 Press the pushbutton on the operator or the hand-held transmitter to start the r
ference run “close”
22 The door closes
23 When the door is fully opened the operator stops and acknowledges the refer
run “close” with a short flash of the light
Note: The r
mitter but only by pressing the internal force limit (force r
If the operator has been stopped during a reference run, not by r
sition but by an obstacle or something else, the setting procedure must be comple-
tely repeated.
Log off the transmitter
All the operator settings can be deleted (Reset)
• Press push button and hold it pressed until after appr
shorter acknowledgement tone is heard, then release the pushbutton
• The light flashes three times (mains operation) or five times (accumulator opera-
tion)
• All settings concerning the transmitter and soft-stop are now deleted
Automatic detection of mains and accumulator operation
The operator itself detects which source of power is connected to it. If the operator is
connected to a source of power
five times for accumulator operation.
Information about accumulator operation
Putting into operation
• Before the accumulator is ready for ope-
ration it should first be fully charged.
Charging is only possible within a tem-
perature range between 5° to 40°C. For
this connect the accumulator pack to the
230V socket with the 230V cable sup-
plied.
• The charging pr
empty accumulator can last up to 15h.
During charging the LED lights up r
The charging pr
terrupted before the accumulator is full,
i.e. before the LED changes to green.
The device should not remain connected
to the mains for longer than 48h.
Note: It can happen with lowly charged or faulty accumulators that the LED first lights
only dimly or does not light red at all. However
again has taken up a little energy
though the LED does not light up. The capacity of the accumulator is reduced for
every charge/dischar
causes a gradual reduction of capacity
scharged within 6 months of pur
mulator be replaced if there is clearly a r
Mounting the accumulator pack
The accumulator pack holder should be fixed as near as possible to the middle of the
door track. Pay attention to get a strong and secure fastening. The holder can also be
fastened to a wall. Pay attention to see that the cable to the operator is sufficiently
long. The spiralled cable should not be stretched too far as otherwise the accumula-
tor will possibly be pulled from the holder or the plug can slip out of the accumulator
pack.
Connecting the operator
T
connection cable in the right hand socket of the accumulator pack (see illustration of
connections).
Power reserve
With intact, fully charged accumulators the operator has a power r
days at 20°C (for 3 run cycles per day
once close). This power reserve is shortened for lower or especially high temperatu-
res. If the accumulator ages, a reduction of the power r
If the capacity of the accumulator decreases the operator gives warning by way of a
regular signal tone. If this signal tone be heard after a run ther
days until the accumulator capacity is no more sufficient for operation. The signal
tone falls silent about one minute after the run. If the accumulator capacity falls too
severely during a run, the operator stops immediately and reports that the accumula-
tor is empty by beeping three times. The operator is then blocked for about 10 se-
conds and cannot be actuated.
Attention! If the accumulator is empty the door can be operated manually using the
emergency unlocking that has been installed
Ratings:
Charging cir
Input voltage: 230V / 50Hz
Current consumption: 15W max.
Internal primary fuse: 250mA
Accumulator charging
Current: 500mA
Charging time: approx.
15 hours
Output for the operator:
Output voltage: 12V
Overcurrent fuse: 8A
Accumulator capacity: 7Ah
Force setting on the motor force r
switch (normally not necessary)
It is possible to influence the force in the closing
direction. The more the spring in the spring dome
is pretensioned, the stronger the closing for
In principle, the force should not be set higher
than necessary
General information
• Before logging on the first transmitter a reset should be made in or
that only the transmitter required is logged on.
• If the motor is blocked, or is faulty
conds and reports this with a fault message in the form of two beep tones.
Anschlussbild
Charge Operator
Force setting
weak middle strong
