Bedienungsanleitung Novoferm Novomatic 553S (Seite 14 von 30) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

709103

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Special adjustments

Menu stage 9: Special functions

Push button .“9” is displayed.

Menu Operating mode

value

0 Normal operation

(factory setting upon delivery)

1 Normal operation with ventilation

position

The ventilation position can be initiated by

pressing the second push button on the

hand transmitter or via the signal 112

internal push button (accessory) 13b.

2 Partial opening of side sectional doors

Partial opening of approx. 1m can be

initiated by pressing the second push

button on the hand transmitter or via the

signal 112 internal push button

(accessory) 13b.

Advice: The 2nd push button of the transmitter has

to be teached-in again after changing the operation

mode.

• Operating Instructions

These Operating Instructions describe how to use

the prodct properly and safely. The safety advice and

information as well as the accident prevention and

general safety regulations for the field of application

must be complied with.

All persons using the gate system

must be shown how to operate it

properly and safely.

Keep hand transmitters out of the reach

of children.

When the operator is being used, the

opening and closing phases must be

monitored. It must be ensured that

neither persons nor objects are located

within the gate’s range of travel.

• Normal operation (0)

(factory-set operating mode)

The garage door operator can be actuated by an

impulse generator such as hand transmitter, key

switch etc. It is only necessary to generate a short,

sharp impulse.

Functional sequence

First impulse:

Operator starts up and causes the door to travel to

set open or closed travel limits.

Impulse generated while door is moving:

The door stops.

Repeated impulse:

Door continues to move but in opposite direction .

• Quick release

During adjustments, in the event of a power failure or

malfunctions, the door can be disengaged from the

operator by actuating the pull cord on the carriage

and then be operated manually.

If the door is to be operated manually over a longer

period of time, then the existing locking pin must be

inserted (see figure 12). The door latches put out of

service for power operation must be refitted,

otherwise the door is not latched in the the closed

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

position.

In order to restore power operation, return the

locking pin to the parking position (a) and put the

latches out of service.

After an impulse has been generated, the door

automatically latches with the door operator.

Internal safety device• Internal safety device

If the closing door encounters an obstruction, the

operator stops and causes the door to open to ist top

end-of-travel position in order to clear the

obstruction. During the last 2 seconds of the closing

cycle, the door only opens slightly, this being

sufficient to clear the obstruction but otherwise

preventing anyone from taking a look into the

garage.

If the opening door encounters an obstruction, the

operator stops immediately and reverses the

travelling direction for approx. one second.

• External safety device

Connection plan ( figure 13)

Wicket door contact STOP A

An open wicket door stops the operator immediately

or prevents it from starting up.

Light barrier (STOP B)

An interruption of the light barrier causes a stopping

and a reversal during the closing cycle. An

interruption of the light barrier during the opening

cycle makes no difference.

• Lighting

The lighting switches on automatically whenever a

start impulse is generated and switches off again

after the set time phase (factory setting approx. 90

seconds).Changing the battery: slide back the

battery compartment cover on the handtransmitter.

Take out the battery. Insert a new battery. Be sure to

pole correctly! Slide the cover back on.

• Signal light

If a signal light for signalling the opening and closing

phases is installed, this flashes along with the lamp

in the operator as soon as a start impulse is

generated. The operator starts with a time delay in

accordance with the set warning phase (see menu

stage 7).

• Hand transmitter

Programming further hand transmitters:

See menu stages 1 and 2 (figure 15 and 16).

Changing the battery: Check the polarity is correct!

Empty batteries must be disposed of separately

(toxic waste)!

• Further operating modes

In menu 9, another operating mode can be chosen.

For the setting applying to menu 9, see parantheses.

•

Normal operation for ventilation position (1)

The ventilation position is designed to allow

ventilation of the garage. For this, the door is

opened approx. 10 cm.

Actuation as for normal operation.

By pressing the 2 button on the hand transmitter

or generating an impulse via another device, the

door can be brought into the ventilation position

from the open or closed state.

From the ventilation position the door can be

closed again via all impulse generators.

Operation on a side-opening sectional door

(2)

Instead of opening the door fully, the door can be

partially opened by approx. 1 m in order to provide

access to the garage.

By pressing the 2 button on the hand transmitter

or generating an impulse via another device, the

door can be brought into the partially open state

from any given position.

• Maintenance / Checks

The door system must be inspected

and tested by a specialist company

prior to initial operation and at least

once a year thereafter.

Monitoring the force limit

The operator control unit features a dual-processor

safety system to monitor the forc elimit.

The integral force cut-out is automatically tested at

each travel limit.

The door system must be checked prior to initial

operation and at least once a year thereafter. In the

process, the force limiting device (figure 20) must be

tested!

Caution! If the closing force is set too

high, persons can be placed at risk of

injury or property could sustain damage.

Tthe force limit for the opening cycle can be

adjusted in menu stage 5, the force limit for the

closing cycle can be adjusted in menu stage 6.

• Cycle counter

The cycle counters stores the number of opening or

closing cycles performed by the operator.

In order to read out the meter, keep the

button pressed for 3 seconds until a number is

displayed. The display throws out the values

beginning from the highest decimal place down to

the lowest one after another. In the end, a horizontal

line is displayed. Example: 3456 cycles, 3 4 5 6 -

Novoferm Novomatic 553S Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info