Bedienungsanleitung Novy 7510 (Seite 20 von 28) (Deutsch, Englisch, Holländisch, Französisch)

571864

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

EN 20

Replacing the lamps

Please allow the lights to cool down sufﬁciently

before touching them. Cover and protect delicate

surfaces underneath the hood when changing

lamps. The hood needs to be disconnected from

the current before proceeding.

1. Carefully slide down the spotlight holder and

then open the spotlight holder with a tilting

movement.

2. Removing the LED lamp:

A. First disconnect the cable to the LED to be

replaced. Disconnect by means of releasing

the lock, by applying light pressure while at

the same time pulling away.

B. Next, remove the LED to be replaced by

making a gentle rotating movement to the left.

3. Mounting the new LED:

A. Place the new LED light into the locking ring.

B. Make a rotating movement to the right until

the LED light is locked.

C. Connect the power cable.

D. Put back the cover at its place.

Remove the Monoblock recirculation ﬁlter:

• Open the bottom plate with both hands and

remove the aluminium grease ﬁlter from the

hood.

• The Monoblock recirculation ﬁlter is found in

its opening in the cooker hood. Remove it from

the cooker hood.

Regenerate the Monoblock recirculation ﬁlter:

• The Monoblock can be regenerated up to 12

times. This is done in the oven.

• Place the ﬁlter in the oven for 1 hour at 120°C.

Provide sufﬁcient fresh air in the room where

the oven has been placed, as smells can be

released. Smells can be released when baking

certain kinds of ﬁsh. The best solution for this is

to immediately regenerate the ﬁlter.

Reset the Monoblock recirculation ﬁlter

The cooker hood (motor) must be running!

Simultaneously press + and – for 5 sec. until the

red indicator lamp ﬂashes 3 times for conﬁrmation.

Place the Monoblock recirculation ﬁlter:

• Open the bottom plate with both hands and

remove the aluminium grease ﬁlter from the

hood.

• Place the Monoblock recirculation ﬁlter is its

opening in the cooker hood.

• Put back the aluminium grease ﬁlter and close

the bottom plate.

Deactivate the programming:

Attention! This is not recommended for a cooker

hood with recirculation.

Simultaneously press + and – for 5 sec. until the

third green LED ﬂashes 3 times.

Maintenance of the bottom side of the cooker

hood

Please allow the lights to cool down sufﬁciently

before cleaning the hood. Use a soft, wet cloth

and a mild detergent to clean the hood.

Never use aggressive, abrasive detergents or

sponges. Bleach will damage stainless steel.

The stainless steel surfaces can be treated with

Novy Inoxcleaner (906.060) after cleaning.

Maintenance of the Solid Surface material

The housing is made from Solid Surface. Cleaning

is done using a cloth or sponge moistened with a

mild detergent. Then rub dry with a dry, soft cloth

to avoid stains. Do not use an abrasive or scourer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Novy 7510 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info