Bedienungsanleitung Numark NS7 3 (Seite 12 von 120) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618121

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Track Controls

33. Strip Search™: The length of this strip represents the length of the entire track. Place your

finger on a point along this sensor to jump to that point in the track. (If you want to scroll

through a track, we recommend using your computer rather than running your finger along

the strip.)

34. Slip / Clear: When using the software’s Beat Grid, press and hold this button and move

the platter to “slip” (i.e., shift or slide) the entire Beat Grid to the left or right.

Press and hold Shift and then press this button to delete the entire Beat Grid.

Important: Your track must have a set Beat Grid for the Slip / Clear button to work.

35. Adjust / Set: Press and hold this button and move the platter to “warp” the entire Beat Grid.

Press and hold Shift and then press this button to set a Beat Marker at the Audio

Playhead’s current location.

Important: Your track must have a set Beat Grid for the Adjust feature to work. Also, using

the Adjust feature will change the track’s BPM.

36. Slip Mode / Motor Off: Press this button to enable or disable Slip Mode. In Slip Mode,

you can jump to Hot Cue Points, trigger Loop Rolls, or use the platters, while the track’s

timeline continues. In other words, when you stop the action, the track will resume normal

playback from where it would have been if you had never done anything (i.e., as if the track

had been playing forward the whole time).

Press and hold Shift and press this button to activate or deactivate the corresponding

platter’s motor. This will not affect the track’s playback.

Pitch Controls

37. Tap: Tap this button at the same tempo as the track to help the software detect a more

accurate BPM reading.

38. Range / Master Tempo: Press this to adjust the range of the Pitch Fader to ±8%, ±16%,

and ±50%.

Press and hold Shift and then press this button to “lock” the track’s pitch to its original

key. The track’s tempo will remain at the speed designated by the Pitch Fader.

39. Takeover LEDs: When you select the other Deck with the Deck Select switch, the position

of the NS7III’s Pitch Fader may not match the Pitch setting for that Deck in the software.

Slowly move the Pitch Fader in the direction indicated by the Takeover LED arrow until it

turns off. At this point, the Pitch Fader matches the Pitch setting in the software and can

control it again.

40. Pitch Fader: Controls the track’s playback speed. An LED next to the fader will light up

when set at 0%.

41. Pitch Bend ( + / – ): Press or hold down either of these buttons to temporarily adjust the

track’s playback speed. When released, the track playback will return to the speed

designated by the Pitch Fader.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark NS7 3 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info