Bedienungsanleitung Numark NS7 3 (Seite 14 von 120) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618121

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Effects Controls

51. FX 1, FX 2, FX 3: These buttons have different functions on each Deck depending on the

current FX Mode.

• Single-FX Mode: FX 1 activates or deactivates the effect; FX 2 activates or

deactivates the first effect parameter (if applicable); FX 3 activates or deactivates the

second effect parameter (if applicable). Press and hold Shift and press FX 1 to select

the desired effect. Alternatively, press and hold Shift and then turn the FX Knob

under the effect name to move quickly through the list.

• Multi-FX Mode: The buttons activate or deactivate the first, second, and third effects

in the effects chain, respectively. Press and hold Shift and press one of the buttons to

select the effect for that point in the effects chain. Alternatively, press and hold Shift

and then turn the FX Knob under the effect name to move quickly through the list.

52. FX 1 Knob, FX 2 Knob, FX 3 Knob: These knobs have different functions on each Deck

depending on the current FX Mode.

• Single-FX Mode: the FX 1 Knob controls the “wet-dry” balance of the effect; the FX

2 Knob controls the first effect parameter; the FX 3 Knob controls the second effect

parameter. When Touch Mode is activated, touch the FX 1 Knob to activate its effect,

and release the knob to deactivate it.

• Multi-FX Mode: The knobs control the “wet-dry” balance of the first, second, and

third effects in the effects chain, respectively. When Touch Mode is activated, touch a

knob to activate its effect, and release the knob to deactivate it.

53. Beat / Mode: Tap this button repeatedly at the desired tempo to set the rate of the effects’

low-frequency oscillators (LFOs). Press and hold this button to reset Beat Multiplier to the

Deck’s BPM. Press and hold Shift and then press this button to switch between Single-FX

Mode and Multi-FX Mode.

54. Beat Knob: Turn this knob to set the Time Division for the selected effects.

55. FX Assign: Use these buttons to apply Effect A and/or B to the corresponding channel.

You can apply Effect A and/or B to the entire Program Mix by using the FX Send buttons

below the Master Volume knob. (Each effect can be applied to any or all of the four

channels and/or the Program Mix.)

56. Channel Filter: Turn this knob to adjust the filter on the corresponding channel. The type

of filter it adjusts will depend on the Filter Mode button.

57. Filter Mode: Press this button to change the Filter Mode (off, Filter Roll Mode, or Filter FX

Mode), which affects the Channel Filter knobs.

• Off: When this button is off, the Channel Filter knob will apply and adjust a low-pass

filter to the corresponding channel when turned counter-clockwise or a high-pass

filter when turned clockwise.

• Filter-Roll Mode: Press this button once to activate Filter-Roll Mode (the button will

light solid red). The Channel Filter knob will apply and adjust a low-pass filter to the

corresponding channel when turned counter-clockwise or a high-pass filter when

turned clockwise. In addition, it will apply a Loop Roll to the filter and will decrease in

length as the knob moves further away from the center position. Press this button

once to deactivate Filter-Roll Mode.

• Filter-FX Mode: Press and hold Shift and then press this button to activate Filter-FX

Mode (the button will flash red). The Channel Filter knob will apply and adjust a low-

pass filter to the corresponding channel when turned counter-clockwise or a high-

pass filter when turned clockwise. In addition, it will adjust Parameter 1 of the effects

applied to that channel as the knob moves further away from the center position.

Press this button once to deactivate Filter-FX Mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark NS7 3 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info