Bedienungsanleitung Oceanic BUD (Seite 15 von 24) (Englisch)

550354

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

BUD OPERATING MANUAL

DV 3 (DELAYED VIOLATION 3)

If you descend deeper than the MOD*, DTR and Current Depth will be displayed as with the Depth ones ﬂashing (Fig. 35).

Max Depth on the ALT will also be displayed as 3 dashes.

*MOD is the Max Operating Depth at which the BUD can properly perform calculations or provide accurate display information. Refer to the

Speciﬁcations in the back.

Upon ascending above the MOD, Current Depth will be restored, however, Max Depth will continue to be displayed as dashes

for the remainder of that dive.

DTR will be restored if it is accurate, or remain as dashes if not.

VGM (VIOLATION GAUGE MODE)

During NORM dives, operation will enter VGM when Deco requires a Stop Depth greater than 70 FT (21 M).

Operation would then continue in VGM during the remainder of that dive and for 24 hours after surfacing. VGM turns the BUD

into a digital instrument without any decompression or oxygen related calculations or displays.

Upon activation of VGM, the full TLBG with the graphics VIO and UP ﬂash for 10 seconds as a warning (Fig. 36).

VGM Dive Main, after 10 sec information includes (Fig. 37) -

> Graphic VIO (in place of DTR) solid.

> Current Depth with FT (or M) icon.

> Graphic UP, ﬂashing until on surface

> VARI while ascending

• B (< 2 sec) to access ALT (EDT & Max Depth).

VGM on Surface

Upon surfacing, the graphic VIO will alternate with Surface Interval time until the unit shuts off after 24 hours.

The SURF icon will ﬂash during the ﬁrst 10 minutes (Fig. 38).

Operation will also enter VGM 5 minutes after surfacing from a dive in which a Delayed Violation occurred.

> A full 24 hour continuous surface interval must then be served before all functions are restored.

HIGH PO2

Warning >> at 1.20 (ATA).

Alarm >> at 1.40 (ATA), except in Deco then at 1.60 only.

During No Deco -

When PO2 (partial pressure of oxygen) increases to the Warning level; the PO2 value will alternate with Current Depth for 10

seconds with the graphic UP displayed (Fig. 39).

After 10 seconds, Current Depth is restored. The graphic UP remains on solid until PO2 decreases below 1.20.

If PO2 continues to increase and reaches the Alarm level (1.40), the PO2 value will again alternate with Current Depth and the

graphic UP will ﬂash (Fig. 40) until PO2 is < 1.40.

During Deco -

If PO2 reaches 1.60 while in Deco, the PO2 value (=> 1.60) with icon will alternate with Current Depth (Fig. 41).

When PO2 decreases below 1.60, Current Depth will restored.

No indication is given to ascend (graphic UP), you control action to be taken according to your expertise and training.

Fig. 35 - DV3 MAIN

Fig. 36 - VGM ACTIVATION

Fig. 37 - VGM DIVE MAIN

alt w/

Fig. 38 - VGM SURFACE

Fig. 39 - PO2 WARNING

Fig. 40 - PO2 ALARM

Fig. 41 - PO2 ALARM DECO

alternate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oceanic BUD Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oceanic BUD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info