Bedienungsanleitung Okbaby Sirius (Seite 7 von 61) (Alle Sprachen)

772999

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

8 9

ENGLISH

Sirius rear child‘s seatSirius rear child‘s seat

al. Do not tighten the screws excessively and check the tightness

periodically.

2) Check that the bicycle is suitable for adding supplementary

loads. Check the information supplied with the bicycle or ask for

information and advice from the bicycle manufacturer.

3) Adjust the seat and its components in order to give the child

the most comfort and safety. When the child is in the seat, the

backrest should be slightly tilted backwards, so as to prevent the

child from sliding forward.

4) Check to ensure that each part of your bicycle is working prop-

erly with the seat mounted.

5) Check the existence of any laws present in your State that govern

the use of bicycle seats to carry children.

6) Check initially and then periodically that the weight and size of

the child does not exceed the maximum allowed by the seat.

7 Check that the child or part of its clothes do not come into con-

tact with moving parts of the seat or bicycle. Avoid the child’s

hands and feet coming into contact with the wheel or being

caught in the brakes.

8) Ensure that there are no sharp edges that could come into

contact with the child (for example, frayed or deteriorated wires

etc.).

9) Ensure that the safety belts are not loose and do not come into

contact with the moving parts of the bicycle, especially with the

wheels, even when the child is not being carried in the seat.

10) Always use the safety belts. Make sure your child is properly

secured with the seat belts.

11) The child in the seat must be clothed and protected from the

cold more than the person riding the bicycle. Protect the child

from rain.

12) It is advised to make the child wear an approved protective hel-

met.

13) Check that the seat is not too hot (e.g., overheated by the sun)

prior to placing the child in it.

14) Remove the seat when the bicycle is transported by car. Strong

wind could damage the seat or detach it from the bicycle, caus-

ing accidents.

15 Cover any saddle springs to avoid a child’s ngers being trapped

and/or squashed by them.

16) Each time the seat is used, check it is tted onto the fastening

block correctly: on pulling the support arm upwards, the fasten-

ing block must hold the seat down rmly.

17) The seat material (polypropylene) loses some of its mechanical

properties with ageing if exposed for longer periods to environ-

mental conditions (sun, rain, ice, etc.). In the case of normal use

and exposure to environmental conditions, the seat should be

replaced after 3 years.

Warnings

1) WARNING: Do not place any additional baggage on the seat. Any

additional baggage must be placed on the opposite side of the

bicycle with respect to the seat. For example: if the seat is in the

rear of the bicycle, use a front bag carrier and vice versa

2) WARNING: Do not modify the seat.

3) WARNING: Riding the bicycle may be dierent with a child in the

seat, especially regarding balance, steering and braking.

4) WARNING: Never park the bicycle leaving the child unattended in

the seat.

5) WARNING: Do not use the seat if any part is missing or broken.

Mounting and assembling the child seat

Illustration 1:

fasten the backrest to the metal support.

Phase 1 : Open the fastening cover (14)

Phase 2 : Raise the backrest until it rests on the metal support

Phase 3 : Close the fastening cover (14) and push it upwards to hook

on the safety lever (24).

Illustration 2:

Incline the backrest as far as possible by pressing the knob down-

wards whilst rotating it (16) clockwise.

Illustration 3:

Insert the support arm (5) pushing it into the correct position (25).

Illustration 4:

Insert the fastening plate (12) pushing it as far as possible and then

hook it on using the safety tab (26) over wall (27) as seen in the

diagram.

Illustration 5:

Screw on the xing bridge (13)

Illustration 6:

Check the diameter of the frame and choose the most suitable

plastic adaptor (10). The reference diameter is indicated on each

adaptor. Fix the fastener block (8) and the fastener counter-block (7)

in place, placing the plastic adaptor (10) and the soft plastic reducer

(17) in between them. The plastic adaptor (10) has specic grooves

to hold the cable glands welded to the frame and the cables. Do

not tighten the fastener screws (9) completely so you can adjust the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Okbaby Sirius Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Okbaby Sirius

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info