Bedienungsanleitung Okbaby Sirius (Seite 8 von 61) (Alle Sprachen)

772999

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

10 11

ENGLISH

Sirius rear child‘s seatSirius rear child‘s seat

vertical position of the child seat; when the height is right; tighten

the screws rmly in place.

Illustration 7:

Take the seat and insert the two ends of the support arm (5) into the

fastening block holes. Place the backrest upright using the knob (16)

(see ill. 2) rotating it in an anti-clockwise direction. Now check that:

- the barycentre reference point (19) on the seat is not over 10cm

from the centre of the wheel.

- the child seat is at least 6-7 cm from the mudguard, from the

wheel or from any luggage racks.

- If the child seat barycentre reference is not between the set

parameters, adjust the horizontal position as follows:

Illustration 8:

When the backrest is in an upright position, loosen the screws (20)

using the supplied wrench.

WARNING! Do not unscrew the screw (20) completely, just loosen

it enough to slide the seat on the plate. Slide the seat forwards or

backwards until you reach the recommended barycentre position.

Tighten the screws (20). Your child seat is now correctly tted onto

your bicycle. Adjust the vertical position following the instructions in

the diagram; when the seat is correctly in place, tighten the screws

(9) slowly and evenly until the fastening block stops rotating around

the frame. Slide the cover (18) over the front part of the fastening

block (8). Cover the counter-block (7) with the protection cover (11).

Illustration 9:

Fastening the footrest. To fasten the footrest insert it in the high-

est position on the shaped adjuster slot, while keeping the x-

ing bridges of the safety belt on the outside of the seat. Insert the

regulating pin (21) from the outside of the seat towards the inside

as illustrated, making sure that the right pin meets the right side

and vice versa. Both the pins and sides of the seat are marked with

DX=right and SX=left. Slide the footrest (4) down.

Illustration 10:

Extracting the footrest. To extract the footrest, turn the adjuster

lever (21) upwards, move the footrest (4) upwards as far as possible,

remove the adjuster lever outwards to free the support.

Use of the seat:

Illustration 11:

Setting the inclination of the child seat. Press and turn the inclina-

tion knob (16) until the backrest is in the desired position.

WARNING! When adjusting the inclination of the backrest, the child

seat moves forward and the footrests may catch when pedalling.

Illustration 12:

Adjusting the footrest: To adjust the height of the footrest (4), turn

the adjuster lever (21) upwards, once you have found the right posi-

tion, turn the adjuster lever downwards to x the footrest in place

Illustration 13:

Fastening and unfastening the child’s feet. Make sure your child’s

feet are well fastened to the footrests. The safety belt is long for

easy adjustment. To release the belt 22, lift it out to free it from the

bridge trapping it.

Illustration 14:

Fasten the child’s safety belt: Adjust the height and length of the

belts according to the size of the child. Setting belt height: the belt

can be extracted to adjust its height by inserting the buckle behind

the backrest through the opening each time (g.14). Choose the up-

per or lower openings to x the belts based on the child’s height. Set

belt length: modify belt length by sliding the buckles. The belts must

be fastened rmly without them being too tight for the child. Fasten

the belts: fasten the belt clasp. Check that the belt clasp clicks shut

properly, and then pull the belt.

Illustration 15:

Unfastening the belts. Press simultaneously the two side and cen-

tral press-buttons on the clasp. The clasp will open.

Illustration 16:

Removing the child seat: Press the release button (1) on the fasten-

ing block (8) and remove the child seat. To hook the seat on again,

insert the support arm (5) in the two xing block holes (8) until the

lever clicks.

Maintenance

1) Clean the seat, the padding and the belts with warm water and a

mild detergent. Do not use solvents or abrasive or corrosive de-

tergents. Leave the padding to dry in the open air. Do not iron.

2) Seat repairs and replacement of damaged components must only

be carried out by authorized personnel.

Technical specications

Product Child bicycle seat OKBABY mod. Sirius

Dimensions 41x45x70 CM (LxDxH)

Weight 5.3Kg

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Okbaby Sirius Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Okbaby Sirius

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info