Bedienungsanleitung Olsberg Turia Lina Compact (Seite 15 von 44) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

707624

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

170

1087

400

281 312 312

min 172

Fig. 5 Wall bracket

1 Fastening holes for wall bracket

2 Air inlet duct

3 Fastening bolts M12

4 Adjusting screws for alignment

and fold it out of the wall bracket.

– Break the cover for the rear stove pipe connection

out of the wall bracket.

– Fold back the thermal insulation and fasten with

the brackets.

– Through the hole of the broken-out cover, cut out

the hole for the rear stove pipe connection in the

thermal insulation.

● The combustion air connection for room air inde-

pendent operation can be executed either to the rear

or below. The device is delivered pre-assembled for

the rear connection.

Proceed as follows for a bottom connection:

– Pull out the drawer under the combustion chamber

door and lift it out.

– Break the lower cover out of the arched oor of the

device.

– Swap the rear connection duct and the lower seal-

ing cover.

● For room air dependent operation:

– Pull out the drawer under the combustion chamber

door and lift it out.

– Unscrew the lower sealing cover in the device.

● Determine the installation location for the stove.

Objects made of ammable materials must not be

present or be placed in the radiation area of the

stove to a distance of 80 cm, measured from the

view pane of the combustion chamber door.

Minimum distance to ammable or bearing walls:

lateral 17 cm

● Install the pipe lining (customer-provided) in the

chimney. For the top stove pipe connection, the con-

nection height can be individually determined, how-

ever it should not exceed 1.5 m from the connec-

tion duct. For the connection height for the rear stove

pipe connection see chapter “Technical data”. There

should be no ammable material within a 20 cm cir-

cle around the stove pipe, for the passage through

structural components made of ammable materials.

● Align the wall bracket as a template at the desired

position on the wall with a spirit level, hold it in place

and mark the positions of the 6 fastening holes (see

Fig. 5).

● Attention: When using the recommended fastening

system in vertical coring brick, drill the 6 fastening

holes through turning, without impact.

● For connection of room air independent operation

with air supply from the rear, the air inlet duct on the

wall bracket must be sealed with silicone on the wall.

● Pre-mount the wall bracket with the suitable fasten-

ing system and the provided D=34 washers for M10

screws, align it using a spirit level and screw it tight

against the wall.

● Lift the stove onto the skids of the wall bracket.

● Slide and align the stove in front of the wall brack-

et in such a manner that the stove pipe ts into the

pipe lining. Connect the stove pipe at both connec-

tion points with stove putty so that the stove pipe is

permanently sealed.

The stove pipe connections must be sealed. The

stove pipe must not project into the chimney.

● If needed the device can be aligned in the skids

(Fig. 5) with the adjusting screws.

● Bolt the stove to the wall bracket with the 4 previ-

ously dismounted washers and M12 fastening nuts.

● If provided, mount the OEC. To do this, pull out the

drawer under the combustion chamber door and lift

it out.

Route the cables, OEC power connection and OEC

temperature sensor, lower right in the oor space of

the device, behind the set up sheet metal clips so

that the cables are not caught by the drawer.

● Mount the side cladding.

● Fit the cover hood back on and only screw it on the

front.

Bear in mind that on partition walls in accordance

with test specication EN 13240, the temperature

of 85°C can be reached, and with light wallpaper

or similar combustible construction materials, this

can result in colour changes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg Turia Lina Compact Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info